Inspecting The Pressed Connection; Maintenance Instructions; Cleaning And Lubrication; Required Maintenance At Ridgid Authorized Service Center - RIDGID RP 200-B Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

To retract the rollers and remove the tool from the fitting if
battery dies or tool malfunctions during pressed connec-
tion, it is necessary to press the pressure release button
(Figure 1). If this happens, the connection will need to be
pressed again to ensure completion.
7. After cycle is complete, squeeze actuator arms to
open and separate actuator from press ring. Remove
the press ring from fitting by manually grasping ring
halves and opening assembly. Avoid any sharp edges
which may have formed on fitting during pressing
operation.

Inspecting The Pressed Connection

1. Inspect the pressed fitting. If the fitting is supplied with
a control ring and/or a control label by the fitting
man ufacturer, remove it. Control rings and labels
are supplied by the manufacturer to indicate that the
fitting has not yet been pressed. Removal of the con-
trol ring and label indicates to others that the con-
nection has been pressed.
Look for the following:
• Excessive misalignment of the tubes. Note that a
slight amount of misalignment at the pressed con-
nection is considered normal.
• Tubes that are not fully inserted into the fitting –
dou ble check the insertion marks made on the
tube to see that they are still aligned with the end of
the fitting.
• Incorrect jaw or ring alignment with the fitting con-
tour, distorted or deformed fitting.
• Any other issues per the fitting manufacturer.
If any of these problems are found, then removal of
the fitting is required and a new fitting and tube will
need to be prepared and pressed in its place.
2. Test system in accordance with normal practice and
local codes.
3. See fitting system's operator's manual for specific
inspection criteria.

Maintenance Instructions

WARNING
Make sure battery is removed from tool before per-
forming maintenance or making any adjustment.
RP 200-B Press Tools

Cleaning And Lubrication

1. Wipe the tool clean daily with a clean dry cloth.
2. Inspect the attachment mounting pin and lubricate the
pin with silicone lubricant as needed.
RP 200-B Press Tool
3. Check return springs in attachments with each use.
Attachments should open and close freely with only
moderate finger effort required.
Required Maintenance At RIDGID
Authorized Service Center
After 30,000 cycles, the LED light will flash three times
then pause continuously, to indicate that it is time for
maintenance and recalibration. The tool will not run if it is
not serviced within 2,000 cycles (32,000 total) after the first
flashing LED.

Accessories

WARNING
The following tool accessories have been de signed
to function with the RP 200-B Press Tools. Other
accessories suitable for use with other tools may
become hazardous when used on the RP 200-B.
To prevent serious injury, use only accessories
specifically designed and recommended for use
with the RP 200-B, such as those listed below.
Ridge Tool Company provides Compact Pressing
attachments designed specifically for use with
RIDGID Compact Press Tools. Only use attach ments
that are specifically designed to press the fitting sys-
tem you are installing. For a complete listing of
RIDGID attachments available for this tool, see the
Ridge Tool Catalog on line at www.RIDGID.com or
call Ridge Tool Technical Services (800) 519-3456.
RP 200-B Press Tool Accessories
Catalog
No.
Description
44693
18V 2.0 Advanced Lithium Battery Pack
44698
18V 4.0 Advanced Lithium Battery Pack
43458
18V Advanced Lithium Charger
31013
18V 1.1 Ah Lithium-Ion Battery Pack
32743
18V 2.2 Ah Lithium-Ion Battery Pack
31018
18V 3.3 Ah Lithium-Ion Battery Pack
32068
18V Lithium-Ion Charger
43453
Carrying Case (Plastic)

Storage

Remove battery from tool and store tool and battery in
case. Avoid storing the tool, batteries or charger in
extreme heat or cold. The tool temperature sensor will not
allow the tool to turn on if oil temperature is not within the
temperature range of 15°F (-10°C) to 122°F (50°C). So it
may be neces sary to allow the tool to warm or cool to a
temperature within the operating range by placing it in a
9

Publicidad

Tabla de contenido
loading

Tabla de contenido