Daewoo DCD-200 Manual De Instrucciones página 5

Wave segment fl ashing means time signals are being
received. The signal quality could be classifi ed into 4
types:
No signal quality
Acceptable signal quality
If the RC clock receives signal successfully, a sync-
time symbol " " will appear on the LCD. The unit has
already received the time signal. Otherwise the signal
strength symbol will disappear from the LCD display.
Note: You may use the "RCC" button to receive the
time signal manually. The unit will exist the receive
mode automatically after 6-12 minutes. Receive mode
consumes more battery power that may reduce
battery lifetime.
TIME AND CALENDAR SETTING
If the clock does not receive the time signal
successfully, you can set the time manually. As soon
as the transmitter is received again, the clock will
automatically synchronize with the received time.
1. In normal time mode, press and hold CLOCK key for
2 seconds until the Year digit fl ashes.
2. Press UP or DOWN key to set the desired value of
the fl ashing digit, press and hold UP or DOWN key
to speed up the setting.
3. Press CLOCK key again until the next digit fl ashes
press UP or DOWN key to change its value.
4. Repeat above operations to set the time and
calendar in this order: Year > Month > Date > 12/24-
hr > Hour > Minute > Second > Language.
5. Press the CLOCK key to save and exit the setting,
or let it exit automatically 30 seconds later without
pressing any key.
Normal time mode
Language setting
Second setting
ALARM TIME SETTING
1. In normal mode, press and hold ALARM key for 2
seconds until Hour digit fl ashes.
2. Press UP or DOWN key to set the desired value,
press and hold UP or DOWN key to speed up the
setting.
3. Press ALARM key again until Minute digit fl ashes.
and press UP or DOWN key to change its value.
Weak signal quality
Excelent signal quality
Year setting Month setting
Date setting
12/24 Hr setting
Minute setting Hour setting
4. Press ALARM key again to save and exit the setting,
or let it exit automatically 30 seconds later without
pressing any key.
Alarm time setting mode
USING ALARM AND SNOOZE FUNCTION
1. Slide ALARM ON/OFF switch to ON position to turn
on the alarm, with the alarm icon "
the LCD.
2. Slide ALARM ON/OFF switch to OFF position to turn
off the alarm.
3. When it is sounding, press SNOOZE/LIGHT to stop
the current alarm and enter the snooze mode,with
the alarm icon fl ashing. Or the sound will stop
automatically one minute later.
4. Once the snooze function is activated, the 4 step
crescendo alarm will sound 5 times in 5-minute
interval. The alarm duration is 60 seconds.
BATTERY REPLACEMENT
When the LCD becomes dim, replace with 2 new AA
size batteries at once. Pay attention to the battery
polarity.
Note
Attention! Please dispose of the used unit or batteries
in an ecologically safe manner.
SUGGESTION
Make sure you read the instructions before
operating this delicate clock. We have developed
this sophisticated instrument for the best reception
performance; however, the signal transmitted from
Germany RC Clock transmitter will be aff ected in
certain situations. We advise you to note the following
instructions:
1. It is strongly recommended to start this clock
at night and let the clock receive the signal
automatically during midnight.
2. Always place the unit away from interfering sources
such as TV set, computer, etc.
3. Avoid placing the unit on or next to metal plates.
4. Closed areas such as airport, basement, tower
block, or factory are not recommended.
5. Do not start reception in moving vehicles such as
cars or trains.
STATEMENT OF COMPLIANCE:
Industrias Masats S.L.U. declares product DCD-200
complies with the essential protective requirements
and objectives of:
• EMC Directive 89/336/EC
To check the entirely declaration of conformity of this
model, visit www.electronicafl amagas.com.
Hour setting Minute setting
" displayed on