Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
disconnected.
Keep vents end discharge
tubes free of debris which can accumulate
and restrict proper air flow.
• Never place any object in the air intake open-
ing as this could restrict proper air flow and
cause damage to the unit.
• Never use for spreading chemicals, fertiliz-
ers, or other substances
which may contain
toxic materials.
• To avoid spreading fire, do not use near leaf
or brush fires, fireplaces,
barbecue
pits,
ashtrays, etc.
• Use only for jobs explained
in this manual.
MAINTAIN
YOUR
UNIT PROPERLY
• Have all maintenance
other than the rec-
ommended
procedures described
in the in-
struction
manual performed
by an autho-
rized service dealer.
• Disconnect
spark plug before
performing
maintenance
except for carburetor adjust-
ments.
• Use only recommended
Weed Eater ® re-
placement
parts;
use of any other parts
may void your warranty end cause damage
to your unit.
• Empty fuel tank before stodng the unit. Use
up fuel left in carburetor by starting engine and
letting it run until it stops,
• Do not use any accessory
or attachment
other than those recommended by manufac-
turer for use with your unit.
• Do not store the unit or fuel in a closed area
where fuel vapors can reach sparks or an
open flame from hot water heaters, electric
motors or switches, furnaces, etc.
• Store in a dry area out of reach of children.
_WARNING:
Stop engine and be sure
SPECIAL
NOTICE:
Exposure
to vibra-
tions through prolonged use of gasoline pow-
ered hand tools could cause blood vessel or
nerve damage
in the fingers,
hands,
and
joints of people prone to circulation disorders
or abnormal
swelling. Prolonged
use in cold
weather has been linked to blood vessel dam-
age in otherwise healthy people. If symptoms
occur
such
as numbness,
pain,
loss
of
strength,
change
in skin color or texture,
or
loss of feeling in the fingers, hands, or joints,
discontinue
the use of this tool and seek
medical
attention.
An antivibration
system
does not guarantee
the avoidance
of these
problems. Users who operate power tools on
a continual
and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
SPECIAL
NOTICE:
For users on U.S. For-
est Land and in some states, including
Cali-
fornia
(Public
Resources
Codes 4442
and
4443), Idaho, Maine, Minnesota,
New Jersey,
Oregon,
and Washington:
Certain
internal
combustion
engines
operated
on forest,
brush, and/or grass covered land in the above
areas
ere required
to be equipped
with a
spark arresting
screen, maintained
in effec-
tive working order, or the engine must be con-
structed,
equipped,
and maintained
for the
prevention of fire. Check with your state or lo-
cal authorities
for regulations
pertaining
to
these requirements.
Failure to follow these
requirements
is a violation of the law. This unit
is not factory equipped with a spark arresting
screen; however, a spark arresting screen is
available
as an optional part. Ifa spark arrest-
ing screen is required in your area, contact
your authorized service dealer for the correct
kit. The spark arresting screen, blower tubes,
and nozzles must be assembled to unit to be
in full compliance
with regulations.
the impeller blades have stopped turning be-
fore opening
the vacuum
inlet door or at-
tempting
to insert or remove the vacuum
or
blower tubes. The rotating blades can cause
serious injury. Always disconnect
the spark
plug before performing
maintenance
or ac-
cessing movable parts.
41_WARNING:
If you receive your unit
assembled,
check each step to insure your
unit is properly assembled
end all fasteners
are secure.
Follow all safety information
in
the manual and on the unit.
•
A standard screwdriver
is required for as-
sembly.
BLOWER
TUBE
ASSEMBLY
1. Align the rib on the blower tube with the
groove in the blower outlet; slide the tube
into place.
NOTE:
Knob must be loose enough to allow
blower tube to be inserted
in blower outlet.
Loosen knob by turning counterclockwise.
'uO,,Wl
r B,ower
Tub ,
Groove _
_-
Rib
2. Secure the tube by turning the knob clock-
wise.
3. To remove the tube, turn the knob counter-
clockwise
to loosen the tube; remove the
tube.
VACUUM
BAG ASSEMBLY
1. Open the zipper on the vacuum
bag and
insert the elbow tube.
2. Push the small end of the elbow
tube
through the small opening in the bag.
-3-
Publicidad
Tabla de contenido
