Engine Maintenance; Oil Recommendations - Briggs & Stratton 073049 Manual De Usuario

Engine Maintenance

WARNING Unintentional sparking could cause
fire or electric shock resulting in death or
serious injury.
WHEN ADJUSTING OR MAKING REPAIRS TO
YOUR WATER PUMP
• Disconnect the spark plug wire from the spark plug
and place the wire where it cannot contact spark plug.
WHEN TESTING FOR ENGINE SPARK
• Use approved spark plug tester.
• DO NOT check for spark with spark plug removed.
Oil

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty
Certified oils for best performance. Other high-quality
detergent oils are acceptable if classified for service SF,
SG, SH, SJ or higher. DO NOT use special additives.
Outdoor temperatures determine the proper oil
viscosity for the engine. Use the chart to select the best
viscosity for the outdoor temperature range expected.
* Below 4° C (40° F) the use of SAE 30 will result in hard
starting.
** Above 27° C (80° F) the use of 10W30 may cause
increased oil consumption. Check oil level more frequently.
Figure
Checking Oil Level
Oil level should be checked prior to each use or
at least every 8 hours of operation. Keep oil level
maintained.
1. Make sure water pump is on a level surface.
2. Clean area around oil fill (A) and remove oil fill cap.
3. Verify oil is at the point of overflowing (B) at oil fill
opening.
4. Replace and tighten oil fill cap.
Adding Engine Oil
1. Make sure water pump is on a level surface.
2. Check oil level as described in Checking Oil Level.
3. If needed, slowly pour oil into oil fill opening to the point
of overflowing at oil fill.
4. Replace and tighten oil fill cap.
12
15
Changing Engine Oil
If you are using your water pump under extremely
dirty or dusty conditions, or in extremely hot weather,
change the oil more often.
CAUTION Avoid prolonged or repeated skin contact
with used motor oil.
• Used motor oil has been shown to cause skin cancer in
certain laboratory animals.
• Thoroughly wash exposed areas with soap and water.
KEEP OUT OF REACH OF CHILDREN. DON'T
POLLUTE. CONSERVE RESOURCES. RETURN
USED OIL TO COLLECTION CENTERS.
Change the oil while the engine is still warm from
running, as follows:
1. Make sure water pump is on a level surface.
2. Disconnect the spark plug wire from the spark plug and
place the wire where it cannot contact spark plug.
3. Clean area around oil drain plug (C). The oil drain plug
is located at base of engine, opposite carburetor.
Figure
15
Remove oil drain plug and drain oil completely into a
4.
suitable container.
5. Reinstall oil drain plug and tighten securely. Remove oil
fill cap.
6. Slowly pour oil (about 0.6 l (20 oz)) into oil fill opening (B) to
the point of overflowing at oil fill cap. DO NOT overfill.
Figure
15
7. Replace and tighten oil fill cap.
8. Wipe up any spilled oil.
9. Reconnect spark plug wire to spark plug.
Figure
Service Air Cleaner
Clean or replace the air cleaner elements as
recommended in the Maintenance Chart or more often
if operating under dirty or dusty conditions. Your engine
will not run properly and may be damaged if you run it
with a dirty air cleaner.
To service the air cleaner, follow these steps:
1. Remove the fastener (A) and the cover (B).
2. Remove the fastener (C) and the filter (D).
3. Remove the pre-cleaner (E), if equipped, from the filter.
To loosen debris, gently tap the filter on a hard surface.
If the filter is excessively dirty, replace with a new filter.
4. Wash the pre-cleaner in liquid detergent and water.
Then allow it to thoroughly air dry. Do not oil the pre-
cleaner.
5. Assemble the dry pre-cleaner to the filter.
6. Install the filter and pre-cleaner into the base(F) and
onto stud(G). Make sure filter fits securely into the base.
Secure the filter with the fastener(C).
7. Install the cover and secure with the fastener(A).Make
sure the fastener is tight.
17
BRIGGSandSTRATTON.COM