Inglesina Zippy Evo Manual De Instrucciones página 30

FEEDING BOTTLE HOLDING UNIT (IF AVAILABLE)
fig. 21 Hook the feeding bottle holding unit (T9) to the
frame and make sure it is properly in its seat.
STORAGE BASKET
fig. 22
The frame is equipped with a capacious storage
basket (T8). To secure it, insert all buttonholes in the proper
hooks and button up the rear strips.
ADDITIONAL TRANSPORT UNITS TO THE FRAME (CARRY
COT, TRANSPORT SEAT, AND INFANT CAR SEAT)
fig. 23
The frame can be used together with carry cot,
transport seat, and Huggy infant car seat.
ZIPPY CARRY COT
HOOKING OF THE CARRY COT TO THE FRAME
Before hooking the carry cot, it is necessary to proceed as
follows:
fig. 24
Remove the armrest covers (T3) if available,
by pressing with the index finger the hooking lever (F9)
positioned inside the armrest (F10).
fig. 25
Insert the two stabilizing supports (T7) in the
openings (F11).
WARNING: the stabilizing supports have to be inserted
only when using the frame with the carry cot.
fig. 26 By holding the carry cot by the handle, attach it to
the armrests (F10), positioning it exclusively facing mum.
fig. 27 WARNING: make sure that the carry cot is always
properly attached on both sides of the frame before use.
UNHOOKING OF THE CARRY COT FROM THE FRAME
fig. 28
Act on the lever (B1) positioned externally to the
carry cot.
fig. 29
Simultaneously, lift the carry cot by holding it by
the handle.
HOOKING OF THE HOOD
fig. 30 Hook the press studs on the carry cot structure.
fig. 31 Wrap the hood (C2) around the handle fastening it
using the suitable press studs.
HANDLE AND HOOD ADJUSTMENT
fig. 32
To adjust the handle and the hood act on the two
lateral button (B2) simultaneously.
fig. 33 WARNING: to transport the carry cot, always
hold it by the handle.
HOOKING OF THE BLANKET
fig. 34
Hook all buttons of the blanket to the carry cot.
MAINTENANCE OF THE INTERNAL LINING
fig. 35 It is recommended to remove the internal lining
periodically to provide for its correct maintenance.
HUGGY INFANT CAR SEAT
HOOKING OF THE INFANT CAR SEAT TO THE FRAME
Before hooking the infant car seat to the frame, it is necessary
to proceed as follows:
fig. 36
If present, remove the stabilizing supports (T7) by
acting on the proper push-buttons (F12).
WARNING: hold the supports during the ejection.
fig. 37 Remove the armrest covers (T3) if available,
by pressing with the index finger the hooking lever (F9)
positioned inside the armrest (F10).
fig. 38 By holding the infant car seat by the handle,
attach it to the frame on the armrests (F10), positioning it
exclusively facing mum.
30
INSTRUCTIONS
fig. 39
always properly hooked before use.
UNHOOKING OF THE INFANT CAR SEAT FROM THE
FRAME
fig. 40
the infant car seat.
fig. 41
by the handle.
To use the Huggy infant car seat properly, refer to the
dedicated manual.
TRANSPORT SEAT
HOOKING OF THE TRANSPORT SEAT TO THE FRAME
Before hooking the transport seat to the frame:
fig. 42
acting on the proper push-buttons (F12).
WARNING: hold the supports during the ejection.
fig. 43
WARNING: when placing the baby, make always sure that
the armrest covers are properly fitted in their seats.
fig. 44
hooked to the frame facing mum or the street.
fig. 45
it in the proper seats on both sides, following the graphical
references available on the structure.
fig. 46
always properly hooked on both sides before use.
UNHOOKING OF THE TRANSPORT SEAT FROM THE FRAME
fig. 47
seat by moving it slightly inwards. Repeat this procedure on
the opposite side, removing it completely.
WARNING: never perform this procedure with baby on
board.
ADJUSTMENT OF THE BACKREST
fig. 48
act on the central device (S2) and bring the backrest to the
wished position.
USE OF THE BUMPER BAR
TRANSPORT SEAT FACING MUM
fig. 49
small handrail (R1) together with its covering.
fig. 50
fig. 51
(S4) on the transport seat.
fig. 52
completely removed. To open it, press the lever (S3) and
extract it; to remove it, repeat the procedure also on the
other side.
TRANSPORT SEAT FACING THE STREET
fig. 53
big handrail (T4) together with its covering.
fig. 54
armrests and press them until they block.
fig. 55
completely removed. To open it, press the red lever (S3)
present under the armrest (F10); to remove it, repeat the
procedure also on the other side.
WARNING: do not insert the fingers in the openings on
the armrests when performing these procedures.
WARNING: make sure that the infant car seat is
Act on the lever (U1) positioned on the rear side of
Simultaneously, lift the infant car seat by holding it
If present, remove the stabilizing supports (T7) by
Insert the armrest covers (T3) in the proper seats.
The transport seat is reversible; therefore, it can be
Hook the transport seat to the frame positioning
WARNING: make sure that the transport seat is
Press the lever (S1) and lift one side of the transport
It is possible to adjust the backrest to 4 positions;
When the transport seat is facing mum, use the
To hook it, press the levers (S3).
Insert the ends of the handrail in their proper seats
The handrail can be opened on one side or
When the transport seat is facing the street, use the
To hook it, insert the ends in the openings on the
The handrail can be opened on one side or