Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
6.
1.
Reinstall spray tip into plastic wand.
2.
7.
Reconnect plastic wand to spray gun.
3.
8.
Make sure garden hose is connected to water inlet. Check
that high pressure hose is connected to spray gun. Turn on
water.
4.
9.
Plug power cord into electrical outlet and turn the master
ON/OFF switch to the ON (I) position by turning the dial
clockwise.
10.
5.
Test the electric pressure washer by operating with each
spray tip.
Pump and Motor Maintenance
The electric pressure washer does not require any maintenance
to the pump or motor. Both assemblies are pre-lubricated and
sealed, requiring no additional lubrication ever.
AFTER EACH USE
Water should not remain in the unit for long periods of time. Sedi-
ments or minerals can deposit on pump parts and "freeze" pump
action. Follow these procedures after every use:
1.
Press the master ON/OFF switch to the OFF (O) position.
Remove power cord plug from electrical outlet.
2.
Turn off water supply, point gun in a safe direction, press
trigger lock button and squeeze trigger to relieve trapped
pressure.
3.
Disconnect garden hose from the water supply and the
electric pressure washer.
4.
Disconnect hose from spray gun and high pressure outlet on
pump. Drain water from hose, gun, and wand. Use a rag to
wipe off the hose.
5.
Drain water from pump by tipping unit on its front side
(water inlet facing down).
6.
Store power cord by wrapping it around cord hook on side
of unit
7.
Store unit in a clean, dry area.
8.
If storing for more than 30 days see Winter or Long Term
Storage on next page.
WINTER OR LONG TERM STORAGE
•
Water should not remain in the unit for long periods of time.
Sediments or minerals can deposit on pump parts and
"freeze" pump action.
Initial Storage Procedures
1.
Drain detergent tank (if used) by tipping unit on its front side
and pouring out all remaining solution.
2.
Run the electric pressure washer with white tipped spray tip.
Flush for one or two minutes.
3.
Turn the master ON/OFF switch to the OFF (O) position by
turning the dial counter-clockwise. Remove power cord plug
from electrical outlet.
4.
Turn off water supply. Point gun in a safe direction, press
trigger lock button and squeeze trigger to relieve trapped
pressure. After a few moments, release trigger on spray gun.
5.
Disconnect garden hose from the water supply and the
electric pressure washer. Disconnect pressure hose from the
pump and the spray gun.
6.
Drain water from hoses and spray gun, then use a cloth or
equivalent to wipe off all exterior surfaces.
7.
Ensure that inlet (garden) and outlet (high pressure) hoses
are disconnected from the pump. Then drain water from
pump by tipping unit on its front side (water inlet facing
down).
NOTICE Water left in the pump could freeze and damage the
pump.
Protecting the Pump
•
To protect the pump from damage caused by mineral depos-
its or freezing, purchase a pump saver solution, available at
hardware stores or on the internet.
•
When using the pump saver solution, make sure that the
pressure washer is turned off and that the inlet and outlet
hoses are disconnected.
•
Read and follow all instructions and warnings supplied with
the pump saver solution that you use.
NOTICE You must protect your unit from freezing temperatures.
Failure to do so will permanently damage your pump and render
the unit inoperable. Freeze damage is not covered by the war-
ranty.
To use PumpSaver, make sure the electric pressure washer is
turned off and inlet and outlet hoses are disconnected.
Read and follow all instructions and warnings given on the Pump-
Saver container.
Final Storage Procedures
1.
Coil power cord and store on back of unit.
2.
Store spray gun and accessories on accessory tray.
3.
Store unit in a clean, dry area that is protected from freezing
temperatures.
4.
Cover unit with a suitable protective cover that does not
retain moisture.
12
STORAGE
Publicidad
Capítulos
Tabla de contenido
Solución de problemas
