Mitsubishi Electric MCF-GA35VB Manual De Instrucciones página 5

PREPARATION BEFORE OPERATION
Remote controller
How to set the batteries and the current
1
time
Remove the front lid and insert batteries.
Then reattach the front lid.
Insert the minus pole of the batteries first.
Check if the polarity of the batteries is correct.
2
Insert the minus pole of
the batteries first.
Press the RESET button.
Press using a
thin stick.
• If the RESET button is not pressed, the remote con-
3
troller may not operate correctly.
Press the CLOCK set button.
Press using a
thin stick.
4
HR. MIN.
Press the and buttons (TIME SET
buttons) to set the current time.
FAN STOP
I FEEL COOL
VANE START
FAN DRY
MODE HR.
ECONO COOL MIN.
RESET CLOCK
HR.
• Each time the button is pressed, the set time
MIN.
increases by 1 hour, and each time the
5
is pressed, the set time increases by 1 minute.
Press the CLOCK set button again and close
the front lid.
Handling of the remote controller
• The range that the signal can reach is about 6 m
when the remote controller is pointed at the front of
the indoor unit.
• When a button is pressed, one or two beeps will be
heard from the indoor unit. If no sound is heard, op-
erate again.
• Use the remote controller carefully.
If it is dropped, thrown or it gets wet, the remote con-
troller may not operate.
• Since the display on the remote controller is made of
liquid crystal (glass), it may not light up if it is dam-
aged from falling.
• Refer to page 10 when the indoor unit does not re-
spond to the remote control signal.
When installing on a wall, etc.
• Install the remote controller holder in a position where
the signal reception sound (beep) can be heard from
ON/OFF
the indoor unit when the button is pressed.
How to install/remove the remote controller
Installing :Insert the remote controller downward.
Removing :Pull it up.
Remote controller
holder
Dry-cell batteries
I Reference for replacing batteries
Replace the batteries with new AAA alkaline batteries in
the following cases:
• When the indoor unit does not respond to the remote
control signal.
• When the display on the remote controller becomes
dim.
• When a button of the remote controller is pressed,
all displays appear on the screen, and then disap-
pear immediately.
Do not use manganese batteries. The remote controller
could malfunction.
• The service life of an alkaline battery is about 1 year.
However, a battery whose time limit is approaching
may be exhausted soon. The recommended usable
time limit is indicated (month/year) on the bottom of
the battery.
• To prevent liquid leakage, take out all batteries when
the remote controller is not going to be used for a
long time.
CAUTION:
If liquid from the batteries gets onto your skin or
clothes, wash it well with clean water.
button
If liquid from the batteries gets into your eyes, wash
them well with clean water and consult a doctor at
once.
• Do not use rechargeable batteries.
• Replace the 2 batteries with new ones of the same
type.
• Dispose of exhausted batteries in the correct man-
ner.
When the remote controller cannot be used (emergency operation)
When the batteries of the remote controller run out or the remote controller malfunctions, the emergency operation
1
can be done using the EMERGENCY OPERATION switch.
Press the EMERGENCY OPERATION switch.
When the EMERGENCY OPERATION switch is
pressed, the unit will operate in test run for 30 minutes
at first and then the operation mode shifts to EMER-
GENCY COOL MODE.
Details of EMERGENCY COOL MODE are as shown below.
However, the temperature control does not work for 30 min-
utes in test run and the unit is set to continuous operation.
The fan speed is set to Hi in test run and shifts to Medium
after 30 minutes.
Operation Mode COOL
Set temperature 24°C
Fan speed Medium
Horizontal vane Auto
The operation mode is indicated by the Operation Indicator
lamp on the indoor unit as following figures.
Operation Indicator Lamp
EMERGENCY COOL STOP
Operation Indicator Operation Indicator
I
To stop the EMERGENCY COOL MODE, press
the EMERGENCY OPERATION switch again.
Each time the switch is pressed, the operation mode
alternates between the EMERGENCY COOL MODE
and STOP MODE.
5