Makita 5007MG Manual De Instrucciones página 63

Indicator lamps
Lighted Off
NOTE: Depending on the conditions of use and the
ambient temperature, the indication may differ slightly
from the actual capacity.
Using Supplied AC power adaptor
(Fig. 5)
Remove the rubber protector and insert the adaptor plug
into the DC socket on the right side of the speaker. Plug
the adaptor into a standard mains socket outlet. Whenever
the adaptor is used, the battery pack is automatically
disconnected. The AC adaptor should be disconnected
from the main supply when not in use.
IMPORTANT:
The mains adaptor is used as the means of connecting
the speaker to the mains supply. The mains socket used
for the speaker must remain accessible during normal
use. In order to disconnect the speaker from the mains
completely, the mains adaptor should be removed from
the mains outlet completely.
USB power supply socket
This jack can be used to charge a mobile phone or any
other device that uses less than 2.1A of DC current.
Charging will only occur when the speaker is switched on.
Note: Ensure the specification of your external device
such as mobile phone, mp3 player or iPod is compatible
with the speaker. Please read instruction manual of your
external device before charging.
IMPORTANT:
Before connecting USB device to the charger, always
•
backup your data of USB device. Otherwise your data
may lose by any possibility.
The charger may not supply power to some USB
•
devices.
When not using or after charging, remove the USB
•
cable and close the cover.
Do not connect power source to USB port. Otherwise
•
there is risk of fire. The USB port is only intended for
6
Remaining
capacity
Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
battery
The battery
may have
malfunctioned
charging lower voltage device. Always place the cover
onto the USB port when not charging the lower voltage
device.
• Do not insert a nail, wire, etc. into USB power supply
port. Otherwise a circuit short may cause smoke and
fire.
• Do not connect this USB socket with your PC
USB port, as it is highly possible that it may cause
breakdown of the units.
Pairing and connecting a device to
the speaker
You need to pair your Bluetooth device with the speaker
before you can auto-link to play/stream Bluetooth music
through the speaker. Paring creates a `bond' so two
devices can recognize each other.
Pairing and playing your Bluetooth
device for the first time
1.
Press the Power button
the Bluetooth indicator will flash in blue. The indicator
flashes fast flashing blue indicating the speaker is
discoverable.
2.
Activate Bluetooth on your device according to the
device's user manual to link to the speaker. Locate the
Bluetooth device list and select the device named
'XRM07.' With some mobiles (which are equipped with
earlier versions than BT2.1 Bluetooth device), you
may need to input the pass code "0000".
3.
Once connected, there will be a beep sound and the
Bluetooth indicator will remain in solid blue. You can
simply select and play any music from your source
device. Volume control can be adjusted from your
source device, or directly from the speaker.
4.
Use the controls on your Bluetooth-enabled device or
on the speaker to play/pause and navigate tracks.
Note:
1.
If 2 Bluetooth devices, pairing for the first time, both
search for the speaker, it will show its availability on
both devices. However, if one device links with this
unit first, then the other Bluetooth device won't find it
on the list.
2.
If your Bluetooth device is temporarily disconnected
to the speaker, then you need to manually reconnect
your device again to the speaker.
3.
If 'XRM07" shows in your Bluetooth device list but your
device cannot connect with it, please delete the item
from your list and pair the device with the speaker
again following the steps described previously.
4.
The effective operation range between the system and
the paired device is approximately 10 meters (30 feet).
Any obstacle between the system and the device can
reduce the operational range.
5.
Bluetooth connectivity performance may vary
depending on the connected Bluetooth devices.
Please refer to the Bluetooth capabilities of your
device before connecting to the speaker. All features
may not be supported on some paired Bluetooth
devices.
to turn on the speaker and