Standard Accessories - HIKOKI CR 13V2 Instrucciones De Manejo

English
○ When cutting metallic materials, use proper machine
oil (turbine oil, etc.). When not using liquid machine oil,
apply grease over the workpiece.
The service life of the saw blade will be drastically
shortened if you don't use machine oil.
○ Never apply any unreasonable force to the saw blade
when cutting. Also remember to press the base against
the lumber fi rmly.
Sawing curved lines
○ We recommend that you use the BI-METAL blade
mentioned in Table 2 for the saw blade since it is tough
and hardly breaks.
○ Delay the feed speed when cutting the material into
small circular arcs. An unreasonably fast feed may break
the blade.
Plunge cutting (Fig. 9 and 10)
○ Avoid plunge cutting for metallic materials. This can
easily damage the blade.
○ Never pull the switch trigger while the tip of the saw
blade tip is pressed against the material. If you do so, the
blade can easily be damaged when it collides with the
material.
○ Make absolutely sure that you cut slowly while holding
the body fi rmly. If you apply any unreasonable force to
the saw blade during the cutting operation, the blade can
easily be damaged.
12. Cut off guide for cutting pipe (optional accessory)
Please refer to the cut off guide user's manual for details
on how to use it correctly.
SYMBOLS
WARNING
The following show symbols used for the machine. Be
sure that you understand their meaning before use.
CR13V2: Reciprocating Saw
To reduce the risk of injury, user must read
instruction manual.
Only for EU countries
Do not dispose of electric tools together with
household waste material!
In observance of European Directive 2012/19/
EU on waste electrical and electronic equipment
and its implementati on in accordance with
national law, electric tools that have reached
the end of their life must be collected separately
and returned to an environmentally compatible
recycling facility.
Switching ON
Switching OFF
Stroke
Disconnect mains plug from electrical outlet
Class II tool

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package
contains the accessories listed in the below.
○ Blade (No. 341) .............................................................1
○ Case .............................................................................1
○ Hexagonal bar wrench ..................................................1
Standard accessories are subject to change without notice.
APPLICATIONS
○ Cutting pipe and angle steel.
○ Cutting various lumbers.
○ Cutting mild steel plates, aluminum plates, and copper
plates.
○ Cutting synthetic resins, such as phenol resin and vinyl
chloride.
For details refer to the section entitled "SELECTION OF
BLADES".
SPECIFICATIONS
Voltage (by areas) *
Power Input
Mild Steel Pipe
Vinyl Chloride
Pipe
Capacity
Wood
Mild Steel Plate
No-Load Speed
Stroke
Weight (without cord)**
* Be sure to check the nameplate on product as it is subject
to change by areas.
** According to EPTA-Procedure 01/2014
NOTE
Due to HiKOKI's continuing program of research and
development, the specifi cations herein are subject to
change without prior notice.
MOUNTING AND OPERATION
Action
Mounting the blade
Taking the broken blade out
Maintenance and inspection of
saw blade mount
Blade hole
Adjusting the base
Switch Operation
Selection of saw blade length
Fastening work piece fi rmly
Plunge cutting
Plunge cutting with the saw blade
installed in reverse
Replacing carbon brushes
Selecting accessories
Refer to Table 1, 2, 3 and 4 for use of the blades.
4
(110 V, 115 V, 120 V, 127 V,
220 V, 230 V, 240 V)
1010 W *
O.D. 130 mm
O.D. 130 mm
Depth 300 mm
Thickness 19 mm
0 – 2800 min
–1
29 mm
3.3 kg
Figure Page
1 116
2 116
3 116
4 116
5 117
6 117
7 117
8 117
9 118
10 118
11 118
― 119