How To Use The Intercom With More Than Two Units; Unit Already Busy - Midland BTNext Manual De Instrucciones

Ocultar thumbs Ver también para BTNext:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

Pair the BTNext to another BTNext unit
To pair the BTNext to another BTNext unit, you must first enter the setup mode:
1. Turn off the unit
2. Press and hold down the middle button about 7 sec., until the Red light is on
permanently.
3. Now press one of the three buttons (Forward, Middle or Rear) for 3 seconds
depending on which button you would like use to open the intercom to the
other unit. The Blue and Red light will flash.
4. Repeat the same procedure on the other unit, you don't need to use the same
button, you can choose one of the three buttons not previously used.
5. When successfully paired, each unit will have the Blue light on for one second
and then go back to the setup mode (Red light always on). Now the unit is
ready for another pairing procedure, and you can pair another BTNext unit
following the same procedure, but using a different button.
If you don't have more devices to pair, you must exit the setup mode before you
can use the units:
› Double click on the Middle button, the Red light will turn off and the Blue
light will start flashing.
You can use now your BTNext.

How to use the Intercom with more than two units

To use the intercom feature, be sure that all the units are turned on and correctly
paired together
Attention: For intercom communication between Driver and Passenger there is no
need to keep the flip-up antenna in the up position. For Bike to Bike intercom the
antenna must be in the upper position.
Manual activation
Press the button corresponding to the unit you would like to communicate with.
After about 4 seconds the intercom communication will open.
The communication remains active until you press again the same button. To
quickly open the intercom to another person, just press the button corresponding
to the other unit, the intercom will be automatically closed and the new connec-
tion will be open (see Table A).
A- Manual activation
Mode
Forward button
Intercom
Short press: Open/Close intercom to paired
raider
Voice activation (VOX)
The voice activation feature can open the intercom only to the unit paired to the
Middle button. While no other communication is open, simply start talking and
the communication will be open and remain active for all the time you are talking.
If there is no conversation the intercom will be closed after 20 seconds. If needed
you can close the intercom manually without waiting 20 seconds, pressing the
Middle button.
If needed, you can temporarily disable the VOX feature simply by pressing the
Rear button for 7 sec. Two sound beep will advise you when the VOX is disabled.
To turn the VOX on again, just press the same button, one beep sound will advise
you that the VOX is now active (or just turn the unit off and on again).
Hint: this feature is very useful when you have a specific person that you like
to talk to more often (for example your passenger). In this way you don't
need to press a button to open the communication.

Unit already busy

If you try to open a intercom connection to another person that is already busy
talking with some one else (or is in a middle of a phone conversation), you will
hear a "busy" double beep tone. Just wait sometime and try again, maybe this
time the "line" is not busy.
The person who is called, will be advised that someone is trying to call and will
hear a voice announcement with the number of the button from which the re-
quest is coming.
In this way as soon as the first conversation is over, the person can easily contact
the caller by opening the intercom of the specific button number (indicated by
the voice announcement).
Middle button
Short press: Open/Close intercom to paired
raider
Long press: Change mode
Midland BT Next - 8
1
2
3
Rear button
Short press: Open/Close intercom to paired
raider
Long press: Toggle on/off wired

Publicidad

Tabla de contenido
loading

Tabla de contenido