Brief Description Of The Press Device; Rotatable Head - NovoPress ACO203XL Instrucciones De Uso

Pos : 28 /RVT/Kurz bes chr eibung/Pressautomati k/ACO202XL @ 0\mod_1381396224584_18.doc x @ 1333 @ 12 @ 1
7

Brief description of the press device

7.1 Automatic press cycle (Fig. 1)
The device features an automatic press cycle. This ensures that the pressing operation is always
completed. For safety reasons, the automatic press cycle only switches on when the pressing
operation has started, i.e. when the fitting starts to be shaped.
After the automatic press cycle has been triggered, the green LED (2) goes out and the pressing
operation runs automatically. The pressing operation can then only be stopped by pressing and
holding the release button (5). After the pressing operation has been completed, the motor
automatically switches off and the green LED (2) lights up again.
If the start button (1) is released before the automatic press cycle begins, the piston in the press
device moves back to its starting position. The pressing operation will not have been completed. The
pressing operation must be triggered again.
Pos : 29 /RVT/Kurz bes chr eibung/Entlastungs knopf/AC O102, ACO152, AC O/ECO202, AC O202XL @ 0\mod_1382425726244_18.doc x @ 1401 @ 2 @ 1
7.2 Release button (Fig. 1)
The pressing operation can be stopped at any time by pressing and holding the release button (5).
The piston in the press device then returns to its starting position.
Pos : 30 /RVT/Kurz bes chr eibung/versc hiebbar er Fing erschutz/AC O202XL @ 1\mod_1428471885347_18.doc x @ 10808 @ 2 @ 1
7.3 Slidable finger guard (Fig. 1)
The press device is equipped with a slidable finger guard (6) as the press jaws differ in length. Slide
the finger guard forwards until you hear it click in as soon as you insert shorter press jaws.
Pos : 31 /RVT/Kurz bes chr eibung/Dr ehbarer Kopf/AC O102, ACO152, AC O202XL @ 0\mod_1382359417950_18.doc x @ 1371 @ 2 @ 1

7.4 Rotatable head

The press tool is equipped with a rotatable crimping head. The head is rotatable by 180°. Within the
range of these 180° the crimping head can be moved into any position. It is only possible to adjust the
crimping head before the pressing operation. The crimping head cannot be rotated while the pressing
operation is being performed.
Pos : 32 /RVT/Kurz bes chr eibung/R üc khubbegrenz ung/AC O202XL @ 1\mod_1428472199814_18.doc x @ 10828 @ 2 @ 1
7.5 Stroke limit (Fig. 1)
The press device features a stroke limit. When using shorter press jaws the stroke limit helps save
time.
The stroke limit can be switched on and off using an indexing bolt (7) as follows:
• Press the start button (1) with the stroke limit being actuated. Immediately:
• Pull out the indexing bolt (7) and rotate through 90°.
• Allow the indexing bolt (7) to lock into the groove.
Press the start button (1) with the stroke limit being actuated. The indexing bolt can then be pulled out.
Pos : 33 /RVT/Kurz bes chr eibung/Akku allgemei n/Ü bers chrift/AC O102, ACO152, ACO202XL, AXI/AAP102, @ 0\mod_1382447195475_18.doc x @ 1453 @ 2 @ 1
7.6 Battery
Pos : 34 /RVT/Kurz bes chr eibung/Akku allgemei n/Info: nic ht geladen + T emperatur en/AC O102, ACO152, AC O/ECO202, AC O202XL, AF P/EFP202, AXI/AAP102 @ 0\mod_1382448018047_18.doc x @ 1473 @ @ 1
Information!
The batteries are not charged at the factory.
Therefore:
– Charge the batteries before using for the first time.
Information!
Limited temperature range for charging and storing the batteries.
Therefore:
– It is imperative that the operating instructions for the battery charger are complied
with.
Pos : 35 /RVT/Kurz bes chr eibung/Akku allgemei n/Akku abnehmen + aufsetzen/ACO102, ACO152, AC O/ECO202, AC O202XL, AF P/EFP202 @ 0\mod_1382442983216_18.doc x @ 1433 @ @ 1
Removing the battery (Fig. 2)
Push in (1) the two release buttons (A) and then remove the battery (2).
15
ACO203XL
EN