Before Starting The Equipment - Hurricane HETH-E 9048 Manual De Instrucciones

Tijera cortasetos telescópica eléctrica
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 41

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
The plug on the power tool must fi t into the
socket. The socket must not be modifi ed in
any way. Do not use adapter plugs with pow-
er tools that have a grounded plug.
Unmodifi ed plugs and matching sockets will redu-
ce the risk of electric shock.
Avoid body contact with grounded surfaces
such as pipes, heating systems, stoves and
refrigerators. There is an increased risk of elec-
tric shock if your body is grounded.
If you use an electric power tool outdoors,
use only extension cables that are suitable
for outdoor use. The use of an extension cable
which is suitable for outdoor use reduces the risk
of electric shock.
If you cannot avoid using the power tool in a
damp location, use a residual current device
(RCD) circuit breaker.
The use of a residual current device (RCD) circuit
breaker will reduce the risk of electric shock.
We recommend that you connect the hedge
trimmer only to an electricity source protected by
a residual current device (RCD) breaker with a
maximum trip current of 30 mA.
Fitting the steady grip (Fig. 3a – 3c)
Remove the fastening screw (Fig. 3a/Item A) from
the steady grip and swing open the fastening clip
(Fig. 3b/Item B). Mount the steady grip on the
motor unit (Fig. 3b/Item 11) as shown in Fig. 3b.
Then rotate the mounting clip back to the closed
position and secure with the fastening screw.
Mounting the extension pole and cutter bar
(Fig. 4a – 4c)
Depending on the height you need to reach, you
can use the hedge trimmer with or without the
extension pole (Fig. 2/Item 9). To use it, loosen
the fastening screw (Fig. 4a/Item C) on the motor
unit. Remove the protective cap (Fig. 2/Item 14)
from the extension pole and insert the extension
pole into the clamp on the motor unit. When in-
serting the extension pole, ensure that the snap
Anl_HETH_E_9048_SPK7.indb 17
Anl_HETH_E_9048_SPK7.indb 17
GB
button latches in the hole in the clamp (Fig. 4b/
Item D). Then fasten the extension pole using the
fastening screw. To mount the cutter bar, loosen
the fastening screw (Fig. 4c/Item C). Remove the
protective cap (Fig. 2/Item 14) from the cutter bar
unit and insert the cutter bar unit into the clamp
on the extension pole. Once again, ensure that
the snap button latches in the hole in the clamp
(Fig. 4b/Item D). Then fasten the cutter bar using
the fastening screw.
Adjusting the tilt angle (Fig. 5a - 5c)
Important: Disconnect the power plug before you
adjust the tilt angle. The cutting blade can be tilted
to make the work as easy as possible.
Pull the safety lever towards the rear (Fig. 5a/Item
12). Then grasp the adjustment lever (Fig. 5b/Item
E). Actuate the locking lever (Fig. 5b/Item 13) and
release it again when you have fi nished adjusting
the tilt angle. Make sure that the lever latches in
place correctly. Then push the safety lever to-
wards the front (Fig. 5c/Item 12).
Important: When you have fi nished, make sure
that the safety lever and the locking lever are lat-
ched correctly.
Important: The gear unit can become hot during
operation.
Fitting the shoulder strap
Important: Always use the shoulder strap when
working with the hedge trimmer. Switch off the
equipment before you take off the shoulder strap.
There is a risk of injury.
1. Hook the carabiner into the strap holder as
shown in Fig. 6/Item G.
2. Slip the shoulder strap over your shoulder.
3. Adjust the length of the shoulder strap so that
the strap attachment is at waist level and you
can work without fatigue.
Note:
The shoulder strap is equipped with a safety
release (Fig. 6 / Item F) which you can use to
quickly detach the shoulder strap from the hedge
trimmer in case of danger. To operate the safety
release, pull it downwards.
- 17 -
25.10.2016 08:58:39
25.10.2016 08:58:39

Publicidad

Tabla de contenido
loading

Tabla de contenido