Triton TSPS 370 Instrucciones De Uso Y De Seguridad página 7

General Safety Warnings of Power
Tools
WARNING! When using electric power tools, basic safety precautions should always be
followed to reduce the risk of fire, electric shock and personal injury including the following
safety information. Read all these instructions before attempting to operate this product and
save these instructions for future use.
WARNING: This appliance is not intended for use by persons (including children) with reduced,
physical or mental capabilities or lack of experience or knowledge unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their
safety. Children must be supervised to ensure that they do not play with the appliance.
WARNING ! When using electric tools basic safety precautions should always be
followed to reduce the risk of fire, electric shock and personal injury including the
following.
For Your Own Safety, read all these instructions before attempting to operate this
product and save these instructions
The term "power tool" in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1 - Keep work area clear - Cluttered areas and benches invite injuries
2 - Consider work area environment
- Do not expose tools to rain
- Do not use tools in damp or wet locations
- Keep work area well lit
- Do not use tools in the presence of flammable liquids or gases
3 - Guard against electric shock - Avoid body contact with earthed or grounded surfaces
(e.g. pipes, radiators, ranges, refrigerators)
4 - Keep other persons away - Do not let persons, especially children, not involved in the
work touch the tool or the extension cord and keep them away from the work area
5 - Store idle tools - When not in use, tools should be stored in a dry locked-up place, out
of reach of children
6 - Do not force the tool - It will perform the job better and safer at the rate for which it
was intended
7 - Use the right tool - Do not force small tools to do the job of a heavy duty tool
- Do not use tools for purposes not intended; for example do not use circular saws to cut
tree limbs or logs
8 - Dress appropriately
- Do not wear loose clothing or jewellery, which can be caught in moving parts
- Suitable safety footwear is recommended when working outdoors.
- Wear protective covering to contain long hair
9 - Use protective equipment
- Use safety glasses
- Use face or dust mask if working operations create dust
WARNING: Not using protective equipment or appropriate clothing can cause personal injury or
increase the severity of an injury.
10 - Connect dust extraction equipment - If the tool is provided for the connection of dust
extraction and collecting equipment, ensure these are connected and properly used
11 - Do not abuse the power cable - Never yank the power cable to disconnect it from the
socket. Keep the power cable away from heat, oil and sharp edges. Damaged or entangled
power cables increase the risk of electric shock
12 - Secure work - Where possible use clamps or a vice to hold the work. It is safer than
using your hand
13 - Do not overreach - Keep proper footing and balance at all times
14 - Maintain tools with care
- Keep cutting tools sharp and clean makes the tool easier to control and less likely to
bind or lock in the workpiece
- Follow instruction for lubricating and changing accessories
- Inspect tool power cables periodically and if damaged have them repaired by an
authorized service facility
- Inspect extension cables periodically and replace if damaged
- Keep handles dry, clean and free from oil and grease
WARNING: Many accidents are caused by poorly maintained power tools.
15 - Disconnect tools - When not in use, before servicing and when changing accessories
such as blades, bits and cutters, disconnect tools from the power supply
WARNING: The use of accessories or attachments not recommended by the manufacturer may
result in a risk of injury to persons.
16 - Remove adjusting keys and wrenches - Form the habit of checking to see that keys
and adjusting wrenches are removed from the tool before switching it on
17 - Avoid unintentional starting - Ensure switch is in "off' position when connecting to a
mains socket or inserting a battery pack, or when picking up or carrying the tool
WARNING: Unintended starting of a tool can cause major injuries.
18 - Use outdoor extension leads - When the tool is used outdoors, use only extension
cords intended for outdoor use and so marked. Use of an extension cable suitable for
outdoor use reduces the risk of electric shock
19 - Stay alert
- Watch what you are doing, use common sense and do not operate the tool when you are
tired
- Do not use a power tool while you are under the influence of drugs, alcohol or
medication
WARNING: A moment of inattention while operating power tools may result in serious personal
injury.
20 - Check damaged parts
- Before further use of tool, it should be carefully checked to determine that it will operate
properly and perform its intended function
- Check for alignment of moving parts, binding of moving parts, breakage of parts,
mounting and any other conditions that may affect its operation
- A guard or other part that is damaged should be properly repaired or replaced by an
authorized service centre unless otherwise indicated in this instruction manual
- Have defective switches replaced by an authorized service centre
WARNING: Do not use the tool if the on/off switch does not turn it on and off. The switch must
be repaired before the tool is used.
21 - Have your tool repaired by a qualified person - This electric tool complies with the
relevant safety rules. Repairs should only be carried out by qualified persons, otherwise
this may result in considerable danger to the user
WARNING: When servicing use only identical replacement parts.
WARNING: If the power cable is damaged it must be replaced by the manufacturer or an
authorised service centre.
22 - Power tool mains plugs must match the mains socket - Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs
and matching sockets will reduce risk of electric shock
23 - If operating a power tool outside use a residual current device (RCD) - Use of an
RCD reduces the risk of electric shock
NOTE: The term "residual current device (RCD)" may be replaced by the term "ground fault
circuit interrupter (GFCI)" or "earth leakage circuit breaker (ELCB)".
WARNING: When used in Australia or New Zealand, it is recommended that this tool is ALWAYS
supplied via Residual Current Device (RCD) with a rated residual current of 30mA or less.
WARNING: Before connecting a tool to a power source (mains switch power point receptacle,
outlet, etc.) be sure that the voltage supply is the same as that specified on the nameplate of
the tool. A power source with a voltage greater than that specified for the tool can result in
serious injury to the user, and damage to the tool. If in doubt, do not plug in the tool. Using a
power source with a voltage less than the nameplate rating is harmful to the motor.
Oscillating Spindle Sander Safety
• Recommendation that the tool always be supplied via a residual current device with
a rated residual current of 30 mA or less.
• If the replacement of the supply cord is necessary, this has to be done by the
manufacturer or his agent in order to avoid a safety hazard.
The warnings, precautions, and instructions discussed in this manual cannot cover all
possible conditions and situations that may occur. The operator must understand that
common sense and caution are factors which cannot be built into this product, but must be
supplied by the operator.
Do not operate the spindle sander until it is fully assembled and you have read and understood
the following instructions and the warning labels on the spindle sander.
a) Check the condition of the spindle sander. If any part is missing, bent, or does not
operate properly, replace the part before using the sander.
b) Determine the type of work you are going to be doing before operating the spindle
sander.
c) Secure your work. Support the workpiece securely on the table, and hold it with both
hands.
d) Be aware of the direction of feed. Feed the workpiece into the sanding sleeve against
the direction of rotation of the sanding sleeve.
e) Always keep your hands out of the path of the sander and away from the sanding
sleeves. Avoid hand positions where a sudden slip could cause your hand to move into
the spindle. Do not reach underneath the workpiece or around the sanding sleeve while
the spindle is rotating.
f) Disconnect the sander after turning off the power switch. Wait for the spindle to stop
rotating before performing maintenance. The sander must be disconnected when not in
use or when changing insert plates, sanding sleeves, rubber spindles, or other items.
g) Make sure there are no nails or other foreign objects in the area of the workpiece to
be sanded.
h) Never use this sander for wet sanding. Failure to comply may result in electrical shock,
causing serious injury or worse.
i) Use only identical replacement parts when servicing this spindle sander.
j) Make sure the spindle has come to a complete stop before touching the workpiece.
k) Take precautions when sanding painted surfaces. Sanding lead-based paint is NOT
RECOMMENDED. The contaminated dust is too difficult to control, and could cause lead
poisoning.
EN
7