Additional Safety Warnings; Standard Accessories - HIKOKI SV 12SH Instrucciones De Manejo

5) Service
a) Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
PRECAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach of
children and infi rm persons.

ADDITIONAL SAFETY WARNINGS

1. Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
2. Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
3. When the work area is removed from the power source,
use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. Installing the sanding paper
Align the sanding paper's holes with the pad's holes.
Strongly push the sanding paper with the palm of your
hand to fasten it securely in place.
5. Attaching and removing the dust bag
Prior to the sanding operation, make sure the material of
surface you are going to sand.
If the surface under sanding operation is expected to
generate harmful / toxic dusts such as lead painted
surface, make sure the dust bag or appropriate dust
extraction system is connected with dust outlet tightly.
Wear the dust mask additionally, if available.
Do not inhale or touch the harmful / toxic dusts generated
in sanding operation, the dust can endanger the health
of yourself and bystanders.
6. Practical operating procedures
○ Never apply water or grinding fl uid when sanding. This
could result in electrical shock.
○ Never turn the power switch ON when the sander is
contacting the surface to be sanded. This is necessary
to preclude damage to the material. The same applies
when switching the power OFF.
○ DO NOT apply excessive pressure to the sander while
sanding. Excessive-pressure may cause overload of the
motor, reduced service life of the sanding paper, and
lowered sanding or polishing effi ciency.
○ Do not press on the corner of the pad with excessive
force. It may cause damage to the pad itself.
SYMBOLS
WARNING
The following show symbols used for the machine.
Be sure that you understand their meaning before
use.
SV12SH : Orbital Sander
To reduce the risk of injury, user must read
instruction manual.
Only for EU countries
Do not dispose of electric tools together with
household waste material!
In observance of European Directive 2012/19/
EU on waste electrical and electronic equipment
and its implementation in accordance with
national law, electric tools that have reached
the end of their life must be collected separately
and returned to an environmentally compatible
recycling facility.
V Rated voltage
P Power input
n
No-load speed
0
Switching ON
Switching OFF
Disconnect mains plug from electrical outlet
Class II tool

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package contains the
accessories listed in the below.
○ 110 × 100 mm Velcro type sanding paper (Square) ..... 1
○ 96 × 96 × 96 mm Velcro type sanding paper
(Triangle) ..................................................................... 2
○ Dust bag ...................................................................... 1
Standard accessories are subject to change without notice.
APPLICATIONS
Mainly used for the following purposes at corners or gaps.
○ Finish polishing of woodwork surfaces
○ Sanding surfaces of woodwork or sheet metal prior to
painting, etc.
SPECIFICATIONS
Voltage (by areas) *
Power Input
No-load speed
Sanding pad size
Sanding paper size
Weight (without cord)**
* Be sure to check the nameplate on product as it is
subject to change by areas.
** According to EPTA-Procedure 01/2014
NOTE
Due to HiKOKI's continuing program of research and
development, the specifi cations herein are subject to
change without prior notice.
3
English
(110 V, 120 V, 220 V, 230 V,
240 V)
200 W*
14000 min
-1
110 mm × 190 mm
110 mm × 100 mm (Square),
96 mm × 96 mm × 96 mm
(Triangle)
1.1 kg