Operation Adjustment; Limitations On The Size Of The Workpiece - stayer TV509 Manual De Instrucciones

– Run the machine for approx. 60 seconds.
Should significant vibrations occur, switch off the machine
immediately; remove and install the cutting disc 6 again.

4.3 Operation adjustment.

Before any work on the machine itself, pull the
mains plug.
Transport Safety (see figure C)
The transport safety-lock 15 enables easier handling of the
machine when transporting to various working locations.
Releasing the Machine (Working Position)
– Push the tool arm by the handle 3 down a little in order to
relieve the transport safetylock 15.
– Pull the transport safety-lock 15 completely outward.
– Guide the tool arm slowly upward.
When working, pay attention that the transport
safety-lock is not pushed inwards. Otherwise, the
tool arm cannot be lowered to the requested depth.
Securing the Machine (Transport Position)
– Guide the tool arm 17 downward until the transport safety-
lock 15 can be pushed completely inward 16.
Transport
– Always carry the power tool by its transport handle 18.
When transporting the power tool, use only the
transport devices and never use the protective
devices.
Adjusting the Cutting Angle (see figure D)
The miter angle can be set in a range from -15° to +45°.
Frequently used mitre angles are identified on the angle
stop 7 with appropriate markings. The -15° and 45° position
are set at the respective end stop.
– Loosen the locking screws 13 for the angle stop with the
supplied ring spanner 14.
– Adjust the desired angle and firmly tighten both locking
screws 13 again.
Displacing the Angle Stop (see figure D)
When cutting workpieces wider than 130 mm, the angle
stop 7 can be displaced to the rear.
– Completely unscrew locking screws 13 with the supplied
ring spanner 14.
– Move the angle stop 7 toward the rear by one or two holes
to the desired clearance.
– Adjust the desired angle and firmly tighten both locking
screws 13 again.
Clamping the Workpiece (see figure E)
To ensure optimum working safety, the workpiece must
always be firmly clamped.
Do not saw workpieces that are too small to clamp.
Long workpieces must be underlaid or supported at their
free end.
– To first approximation the fast thread 9 lift and push the
spindle. Lower 9 for tightening
– Place the workpiece against the angle stop 7.
– Slide the clamping spindle 8 against the workpiece and
firmly clamp the workpiece with the spindle handle 10.
ENGLISH
23
Loosening the Workpiece
– Loosen the spindle handle 10.
– Tilt up the quick release 9 and pull the clamping spindle 8
away from the workpiece.
Adjusting the Depth Stop (see figure H)
In the delivery condition of the machine, the depth stop 16 is
adjusted in such a manner that a new 355 mm cutting disc 6
does not touch the base plate 12 when cutting.
To compensate the wear of the cutting disc 6, the depth stop
16 can be set deeper.
When using a new cutting disc 6, the depth stop 16 must
then always be set back to the original position.
Always adjust the depth stop 16 in such a manner
that the cutting disc 6 does not touch the base plate
12 when cutting.
– Bring the power tool into the working position. (see
"Releasing the Machine (Working Position)")
– Loosen lock nut 25 with the spanner.
– Swing the tool arm with the handle 3 to the requested
position.
– Screw the depth stop 16 in clockwise or anticlockwise
direction until the screw head touches the housing.
– Slowly guide the tool arm upward and tighten the lock nut
25.
Cutting capacity, max. (0°/0°): 140 mm
Cutting Metal
– Set the desired mitre angle.
– Firmly clamp the workpiece as appropriate for its
dimensions.
– Switch on the machine.
– Slowly guide the tool arm downward with the handle 3.
– Cut the workpiece applying uniform feed.
– Switch the machine off and wait until the cutting disc
comes to a complete stop.
– Guide the tool arm slowly upward.

4.4 Limitations on the size of the workpiece

Dimensions of suitable cutting discs
Cutting disc diameter, max.
Cutting discs width, max.
Mounting hole diameter
Permissible Workpiece Dimensions
Maximal workpiece sizes:
TV509
Mitre/Bevel Angle
90º
Workpiece Form
115 Ø
100 x 100
210 x 60
Minimal workpiece sizes (= all workpieces that can be clamped
via the clamping spindle 8): Length 80 mm
23
mm
mm
mm
TV509B TV509C
Mitre/Bevel Angle Mitre/Bevel Angle
45º 0º 0º
45º
90 Ø 140 Ø 110 Ø 120 Ø
80 x 80 130 x 130 100 x 100 105 x 105
85 x 70 254 x 73 105 x 85 130 x 90
355
3
25,4
45º
80 Ø
50 x 50
80 x 50