Intended Use; Dhs782 Dhs783 - Makita DHS782 Manual De Instrucciones

ENGLISH (Original instructions)
SPECIFICATIONS
Model:
Blade diameter
Max. Cutting depth at 0°
at 45° bevel
at 48° bevel
No load speed
Overall length
Rated voltage
Net weight
‡ 'XH WR RXU FRQWLQXLQJ SURJUDP RI UHVHDUFK DQG GHYHORSPHQW WKH VSHFL¿FDWLRQV KHUHLQ DUH VXEMHFW WR FKDQJH
without notice.
‡ 6SHFL¿FDWLRQV DQG EDWWHU\ FDUWULGJH PD\ GLIIHU IURP FRXQWU\ WR FRXQWU\
‡ 7KH ZHLJKW PD\ GLIIHU GHSHQGLQJ RQ WKH DWWDFKPHQW V  LQFOXGLQJ WKH EDWWHU\ FDUWULGJH 7KH OLJKWHVW DQG KHDYL-
est combinations, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
%DWWHU\ FDUWULGJH
Charger
• 6RPH RI WKH EDWWHU\ FDUWULGJHV DQG FKDUJHUV OLVWHG DERYH PD\ QRW EH DYDLODEOH GHSHQGLQJ RQ \RXU UHJLRQ RI UHVLGHQFH
WARNING:
Only use the battery cartridges and chargers listed above. 8VH RI DQ\ RWKHU EDWWHU\ FDUWULGJHV
DQG FKDUJHUV PD\ FDXVH LQMXU\ DQGRU ¿UH

Intended use

7KH WRRO LV LQWHQGHG IRU SHUIRUPLQJ OHQJWKZD\V DQG
FURVVZD\V VWUDLJKW FXWV DQG PLWHU FXWV ZLWK DQJOHV LQ
ZRRG ZKLOH LQ ¿UP FRQWDFW ZLWK WKH ZRUNSLHFH :LWK
appropriate Makita genuine saw blades, other materials
can also be sawed.
Noise
7KH W\SLFDO $ZHLJKWHG QRLVH OHYHO GHWHUPLQHG DFFRUG-
ing to EN62841-2-5:
Model DHS782
6RXQG SUHVVXUH OHYHO /  G% $
pA
6RXQG SRZHU OHYHO /  G% $
:$
8QFHUWDLQW\ .  G% $
Model DHS783
6RXQG SUHVVXUH OHYHO /  G% $
pA
6RXQG SRZHU OHYHO /  G% $
:$
8QFHUWDLQW\ .  G% $
NOTE: 7KH GHFODUHG QRLVH HPLVVLRQ YDOXH V KDV
been measured in accordance with a standard test
PHWKRG DQG PD\ EH XVHG IRU FRPSDULQJ RQH WRRO ZLWK
another.
NOTE: 7KH GHFODUHG QRLVH HPLVVLRQ YDOXH V
PD\ DOVR EH XVHG LQ D SUHOLPLQDU\ DVVHVVPHQW RI
exposure.
DHS782
185 - 190 mm
60.0 - 62.5 mm
43.0 - 44.5 mm
41.0 - 42.0 mm
6,000 min
348 mm
D.C. 36 V
4.5 - 5.1 kg
BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 /
BL1840B / BL1850 / BL1850B / BL1860B
DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the tool is
used especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (tak-
ing account of all parts of the operating cycle such
as the times when the tool is switched off and when
it is running idle in addition to the trigger time).
Vibration
7KH YLEUDWLRQ WRWDO YDOXH WULD[LDO YHFWRU VXP GHWHU-
mined according to EN62841-2-5:
Model DHS782
:RUN PRGH FXWWLQJ ZRRG
9LEUDWLRQ HPLVVLRQ D  PV
K:
2
8QFHUWDLQW\ .  PV
:RUN PRGH FXWWLQJ PHWDO
9LEUDWLRQ HPLVVLRQ D  PV
h,M
2
8QFHUWDLQW\ .  PV
Model DHS783
:RUN PRGH FXWWLQJ ZRRG
9LEUDWLRQ HPLVVLRQ D  PV
K:
2
8QFHUWDLQW\ .  PV
:RUN PRGH FXWWLQJ PHWDO
9LEUDWLRQ HPLVVLRQ D  PV
h,M
2
8QFHUWDLQW\ .  PV
10 ENGLISH
DHS783
-1
2
or less
2
or less
2
or less
2
or less