Inglesina Sketch Manual De Instrucciones página 17

Do not use abrasive cleaners or scrubbing pads.
• It is recommended to wash the lining separately from
other items.
• Periodically revive the fabric parts using a soft clothes
brush.
• Follow the lining washing instructions on the labels.
Handwash in cold water
Do not bleach
Do not tumble dry
Dry flat in shade
Do not iron
Do not dry clean
Do not spin-dry
LIST OF COMPONENTS
fig. 1
A Hood
B Handrail
C Storage basket
OPENING THE STROLLER
fig. 2 To open the stroller, release the hook (P1) that
ensures its folding and unbutton the 2 press studs (P2) that
hold the backrest on the structure.
fig. 3 Holding the handle firmly on both sides, lift the
stroller until the correct opening click is heard.
REMOVING/ATTACHING THE FRONT WHEEL ASSEMBLY
In case of need, the front wheel assembly (D) can be easily
removed.
fig. 4 To remove it, pull it out from the front support
while holding down the lever (D1).
fig. 5 To reinstall it, simply position it and push it until it
clicks into place.
fig. 6 Caution: make sure that the wheels are properly
attached before use.
REMOVING/ATTACHING THE REAR WHEELS
Should it be necessary, the rear wheels (E) can easily be
removed.
fig. 7 To remove them, pull them out from the rear
support while holding down the button (E1).
fig. 8 To reinstall them, simply position them and push
them until they click into place.
fig. 9 Caution: make sure that the wheels are properly
attached before use.
REAR WHEELS BRAKE
fig. 10 To operate the brake, use the rear central lever (P3).
Always engage the brake during stops.
HANDRAIL
fig. 11 The handrail (B) can be open on one side or fully
removed; to open it, press the button (B1) and remove it
from its housing; to remove it, repeat the procedure on the
• Dry the textile lining completely before using or storing it.
• To prevent formation of mildew, it is advisable to air the
carrycot periodically. In particular, separate the textile lining
from the structure and run a dry cloth over the bottom.
INSTRUCTIONS
other side.
ADJUSTING THE BACKREST
fig. 12
pressing the button (P4) on the central device (P5).
fig. 13
central device (P5) and simultaneously pull the rear ring (P6).
SAFETY BELTS
fig. 14
eyelets at the height of the shoulders or immediately above.
If the position is not correct, remove the belts from the first
pair of eyelets and reinsert them in the second one; always
use eyelets at the same height.
fig. 15
the other, open the back zip (P7) on the backrest and remove
the back straps through the corresponding holes, on the
internal rigid reinforcement (P8).
fig. 16
slots on the backrest and pass through the corresponding
holes on the internal rigid reinforcement (P8).
fig. 17
in the ends of the waist one (P9).
fig. 18
buckle (P10).
fig. 19
with the waist strap, making sure that they are all well
adjusted around the baby.
Caution! Failure to comply with this precaution can cause
the baby to fall or slide out, with serious injury risks.
Caution: adapt the height and the length of the harness
according to the baby's growth.
HOOD
fig. 20
desired position.
fig. 21
degree of cover, improving protection from the sun.
HOOD LINING MAINTENANCE
The hood lining can be removed to allow for its correct
To lower the backrest, release the rear strap by
To lift the backrest, press the button (P4) on the
Ensure that the safety belts are inserted in the
To move the back straps from one pair of slots to
Then insert the back straps into the second pair of
Make sure that the back strap is properly inserted
Fasten the ends of the waist belt to the central
Always use the crotch strap (P11) in combination
To adjust the hood, simply accompany it to the
The hood features a fabric insert that extends the
17