Tabla de contenido
Publicidad
5.3
Platform illumination (optional)
There are four lamps integrated on the interior side
of the drive rails to give equal illumination of the
work area.
The illumination is switched on via the main
switch (11) of the platform.
5.4
Lifting the vehicle
• During the entire lifting or lowering process, the
work area of the lift should be clear of people
and objects.
• Afterwards, lift the vehicle to the desired working
height.
Absolutely ensure secure vehicle
placement on the drive-in rails, other-
wise there is a danger of the vehicle
falling.
• Switch on controls at the main switch (11).
• Lift the vehicle. Push the "LIFT" button
• Raise the vehicle to the desired working height.
• The entire lifting process must be continuously ob-
served.
5.5
Set down into the safety ratchets
• Pushing the "Lower into catches" button
sets the lift down into the next possible cat-
ches.
• Keep the "Lower into catches" button
all four safety ratchets (24) are latched in and the
lift can no longer move downwards.
Before working on the vehicle always
lower the lift into the safety ratchets.
5.6
Wheel lifter
27 Booms
• Drive the vehicle over the drive rails lengthwise
and cross-wise in the centre.
The complete vehicle must absolutely
be completely on the drive in rails,
otherwise there is danger of the vehi-
cle falling.
• For short vehicles, the booms (27) must be pushed
in so the wheels can move freely.
174
• For very long vehicles, the booms (27) must be ex-
• Secure the vehicle against rolling away: Put into
• Inspect the hazardous area. No person or object
• Position the synthetic overlays below the fixture
• At the wheel free lift, move the RFH switch (14) to "I".
• Lift the vehicle until the wheels are free by pushing
• Continue to push the "LIFT" button
(12).
o
• Push the "LOWER" button
• An acoustic warning signal sounds during lowe-
(15)
• Continue to push the "LOWER" button
u
u
(15) until
• Continuously observe the entire process.
5.7
• Push the "LIFT" button
27
5.8
!
If the lift will be or is set in down in the safety rat-
chets, then the lift must be moved out before lowe-
008
ring by lifting out of the ratchets according to § 5.7
• Push the "LOWER" button
• The 4 safety ratchets are pulled back electrically
• Lower the lift to the desired position.
• The entire lowering process must be continuously
• Shortly before reaching the lowest position the lift
OPI_COMBI LIFT 4.50/4.65 S PLUS AMS - HYMAX II 4500/4650 S PLUS AMS_V1.1_DE-EN-FR-ES-IT
tended to accept the vehicle.
gear and apply the handbrake.
may stand in the working area of the lift, or on the lift.
points prescribed by the vehicle manufacturer.
The plastic pads may not be tilted, as
this can lead to the vehicle falling. The
vehicle must sit securely on the plastic
overlay otherwise there is also danger
of falling.
the "LIFT" button
o
(12) then check the vehicle is
securely placed on the lift.
vehicle reaches the desired working height.
ring process.
ring and after approx. 1.5 sec the wheel jack
starts to lower.
vehicle reaches the desired working height or un-
til reaching the lowest position.
Lift out of the safety ratchets
Check the hazardous area around the
platform and ensure that there are no
people or objects in the immediate
vicinity of, or on, the platform.
o
released.
Lowering the vehicle
Check that there are no people or objects in the
hazardous area of the lift.
ring process.
and after approx. 1.5 sec the lift starts to lower.
observed.
automatically switches off to prevent crushing in
the foot area (CE STOP).
(12) until the
o
u
(13) to start the lowe-
until the
u
(12) until the catches are
u
(13) to start the lowe-
Publicidad
Tabla de contenido
