About The Standby / Control Power Switch; Electrical Requirements - ETC SmartPack Manual Del Usuario

About the Standby / Control
Power Switch
Use the Standby / Control power switch to start up and shut down
operation of the SmartPack.
When STANDBY breaker on the far left is in the
up/STANDBY -ON position the blue LED is illuminated indicating
power is on.
Importan t note:
position the unit is still connected to the power supply.
When working on exposed load circuit wiring the load cables must
be unplugged or the unit disconnected from the power supply.
I n s t a l l i n g t h e P o w er S u p p l y C a b l e
Danger !
Risk of shock, damage or injury if cable is incorrectly
fitted.
Slide enclosed heat shrink tubing over power cord so that it lines
up with the back panel strain relief.
Power supply cable must be fitted and tested by a competent
person.
The supply must be suitably protected by an external over-current
device.
The apparatus shall not be exposed to dripping or splashing
liquids and no objects filled with liquids, such as vases, shall be
placed on the apparatus.
W o r k A r e a :
To Circuit Breakers
(Factory Wiring)
4
When in the down/standby -OFF
Strain Relief
Installation Wiring
Earth / Ground
L3
L2
L1
N

Electrical Requirements

C E E l e c t r i c a l R e q u i r e m e n t s
3 phase - fitted with 5 core x 6mm
tough rubber sheath cable, style HO7
230V / 400V 50-60Hz 3P+N+PE max. 32A per phase
Colour code:
Green/Yellow = Protective Earth (PE)
Blue = neutral
Black = L1
Brown = L2
Grey or Black = L3
Fitted with Line male CEE 32A 5 pin red connector
Single phase units fitted with 3 core x 10mm
insulated tough rubber sheath cable, style HO7
230V 50-60Hz 1P+N+PE 63A.
Colour code:
Green/Yellow = PE
Blue = neutral
Brown = phase
Fitted with line male CEE 63A 3 pin blue connector
Cable to be 1.2m long
3 phase units require 32 A per phase. Single phase units are
limited to a maximum current of 63 A.
U L E l e c t r i c a l R e q u i r e m e n t s
Power Input
40A, 120/208 VAC, 3Ø, 4 wire & ground, 50/60Hz, 8/5 or 6/5 SO,
SJO (or other approved cable)
60A, 120/240 VAC, 1Ø, 3 wire & ground, 50/60Hz, 6/4 SO, SJO
(or other approved cable)
Color Code:
Green = Ground/Earth
White = Neutral
Black = L1
Red = L2
Blue = L3
Stage Pin SmartPack:
Grounded stage pin receptacles - 20A, 120V, 2-pole, 3-wire
Edison SmartPack:
Grounded Edison receptacles - 20A, 120V, 2-pole, 3-wire
Twistlock SmartPack:
®
Grounded Twistlock receptacles - 20A, 120V, 2-pole, 3-wire
PowerCon SmartPack:
®
Grounded PowerCon receptacles - 20A, 120V, 2-pole, 3-wire
6 circuit multi-pin SmartPack:
6 circuit multi-pin connectors - 20A, 120V
Pins 1, 3, 5, 7, 9, 11 are hot
Pins 2, 4, 6, 8, 10, 12 are neutral
Pins 13 - 18 are ground
2
double insulated
2
double
English Anglais Englisch Inglés