DSC Power Serie Manual Del Usuario página 2

FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by Dig-
ital Security Controls could void your authority to use this equipment.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communi-
cations. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be deter-mined by turning the
equipment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
• Re-orient the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/television technician for
help.
The user may find the following booklet prepared by the FCC useful:
"How to Identify and Resolve Radio/Television Interference Problems".
This booklet is available from the U.S. Government Printing Office,
Washington D.C. 20402, Stock # 004-000-00345-4.
The keypads represented in this manual can be used with the following
Control Units: PC1616, PC1832, PC1864.
IMPORTANT INFORMATION
This equipment complies with Part 68 of the FCC Rules and, if the prod-
uct was approved July 23, 2001 or later, the requirements adopted by the
ACTA. On the side of this equipment is a label that contains, among oth-
er information, a product identifier. If requested, this number must be
provided to the Telephone Company.
PC1616 Product IdentifierUS: F53AL01BPC1614
PC1832 Product IdentifierUS: F53AL01BPC1832
PC1864 Product IdentifierUS: F53AL01BPC1864
USOC Jack: RJ-31X
Telephone Connection Requirements
A plug and jack used to connect this equipment to the premises wiring
and telephone network must comply with the applicable FCC Part 68
rules and requirements adopted by the ACTA. A compliant telephone
cord and modular plug is provided with this product. It is designed to be
connected to a compatible modular jack that is also compliant. See in-
stallation instructions for details.
Ringer Equivalence Number (REN)
The REN is used to determine the number of devices that may be con-
nected to a telephone line. Excessive RENs on a telephone line may re-
sult in the devices not ringing in response to an incoming call. In most
but not all areas, the sum of RENs should not exceed five (5.0). To be
certain of the number of devices that may be connected to a line, as de-
termined by the total RENs, contact the local Telephone Company. For
products approved after July 23, 2001, the REN for this product is part
of the product identifier that has the format US: AAAEQ##TXXXX.
The digits represented by ## are the REN without a decimal point (e.g.,
03 is a REN of 0.3). For earlier products, the REN is separately shown
on the label.
Incidence of Harm
If this equipment (PC1616, PC1832, PC1864) causes harm to the tele-
phone network, the telephone company will notify you in advance that
temporary discontinuance of service may be required. But if advance no-
tice is not practical, the Telephone Company will notify the customer as
soon as possible. Also, you will be advised of your right to file a complaint
with the FCC if you believe it is necessary.
Changes in Telephone Company Equipment or Facilities
The Telephone Company may make changes in its facilities, equipment,
operations or procedures that could affect the operation of the equipment.
Este producto cumple la siguiente normativa: Directiva EMC 2004/108/CE basada en los resultados obtenidos al utilizar normas
armonizadas de conformidad con el artículo 10(5), Directiva R&TTE 1999/5/CE basada en el siguiente Anexo III de la directiva
y Directiva LVD 2006/95/CE basada en los resultados obtenidos al utilizar normas armonizadas.
Este producto cumple con los requisitos de los equipos de Clase II, Grado 2 conforme a las normas EN50131-1: 2004.
El dispositivo es adecuado para su uso en sistemas con las siguientes opciones de notificación:
- A (se requiere el uso de dos dispositivos de aviso y un marcador interno)
- B (se requiere dispositivo de aviso con alimentación propia y un marcador interno)
- D (se requiere el uso de comunicador alternativo con cifrado activado; DSC modelos T-Link TL250, TL260, TL260GS, GS2060)
If this happens the Telephone Company will provide advance notice in or-
der for you to make necessary modifications to maintain uninterrupted
service.
Equipment Maintenance Facility
If trouble is experienced with this equipment (PC1616, PC1832, PC1864)
for repair or warranty information, contact the facility indicated below. If
the equipment is causing harm to the telephone network, the Telephone
Company may request that you disconnect the equipment until the prob-
lem is solved. This equipment is of a type that is not intended to be re-
paired by the end user.
DSC c/o APL Logistics 757 Douglas Hill Rd, Lithia Springs, GA
30122
Additional Information
Connection to party line service is subject to state tariffs. Contact the state
public utility commission, public service commission or corporation com-
mission for information.
Alarm dialing equipment must be able to seize the telephone line and
place a call in an emergency situation. It must be able to do this even if
other equipment (telephone, answering system, computer modem, etc.)
already has the telephone line in use. To do so, alarm dialing equipment
must be connected to a properly installed RJ-31X jack that is electrically
in series with and ahead of all other equipment attached to the same tele-
phone line. Proper installation is depicted in the figure below. If you have
any questions concerning these instructions, you should consult your tele-
phone company or a qualified installer about installing the RJ-31X jack
and alarm dialing equipment for you.