Valex LA3300 Manual De Uso Y Mantenimiento página 6

homologated type. Keep it away from the work area, from damp,
wet, greasy and sharp surfaces and also from sources of heat and
combustibles
8) The socket of the extension lead must be the homologated
10-16A/250V two-pole type. The cross section of the wire must
be equal to or greater than 1 mm². Use a matched cable no lighter
than the H05VV-F type
9) Always get hold of the actual plug when unplugging the power
supply cable from the mains socket.
10) Do not use the power supply cable to lift or pull the tool.
11) This tool is manufactured with the double insulation system.
Double insulation offers additional electrical safety and means
that there is no need to earth the tool.
STARTING
Check the full supply, the integrity of the machine and all accessories
before starting the tool.
Make sure that the main ON/OFF switch is turned off (0) then:
Plug the polisher plug into the electrical mains socket.
To start: press the switch (Fig.A pos.2)
To stop: release the switch (Fig.A pos.2)
OPERATIONAL WARNINGS
Once you have carefully read the safety standards, strictly follow the tips
given below to ensure utmost performance of your polisher.
Proceed calmly. Only once you have become familiar with the tool will
you be able to fully exploit its potentials.
- Start the tool only once you have got a firm hold of the handle and
rest it on the object to be polished.
- Do not polish damp or wet objects.
- Do not press the tool hard down on the surface to be polished
MAINTENANCE
WARNING! Unplug the tool from the mains socket before
proceeding with any sort of inspection or maintenance jobs.
Take good care of your tool and clean it regularly. In this way its
efficiency will be ensured and its wear extended.
- When using the tool and also when the job has been finished carefully
clean the tool's air vents.
- Clean the tool using exclusively a cloth damped with warm water
and a soft brush.
- Do not wet or spray water over the tool.
- Do not use detergents, scourers or other solvents to clean the tool as
you could irreparably damage it. Chemical agents easily deteriorate
the plastic parts.
- Contact an authorised service centre for any repair or maintenance
jobs that are not specified herewith.
TROUBLE SHOOTING
WARNING! UNPLUG THE TOOL FROM THE MAINS SOCKET
BEFORE DOING ANYTHING!
If the polisher fails to start: check if all the electrical connections are
firmly plugged into the mains. Check if the life-saver switch has tripped.
Check if a fuse has blown in your own electrical system. It the problem
persists following these checks then the problem could be in the tool
so have an authorised service centre check it out.
STORAGE
Follow the tips below to store the tool:
1) Clean the tool and all its accessories thoroughly (see maintenance
section).
2) Store the tool away from children's reach, in a stable and safe
position and in a dry and cool place. Avoid excessively high or
low temperatures.
3) Protect the tool from direct light, keeping it possibly in the dark
or semi-dark.
4) Do not close it in nylon bags where humidity could be
produced.
DISPOSAL
Electric and electronic refuse may contain potentially hazardous
substances for the environment and human health. It should therefore
not be disposed of with domestic waste, but by means of differentiated
collection at specific centres or returned to the vendor in the event of
purchasing a new identical appliance. Illegal fly tipping is a criminal
offence and is subject to prosecution.
GUARANTEE
The product is protected by law against all non-conformities with
respect to its stated characteristics, as long as it has been used solely
in the way described in this user's manual, it has not been tampered
with in any way, it has not been repaired by unauthorised personnel
and, where necessary, only original spare parts have been used.
Consumables and/or components subject to particular wear, such
as batteries, bulbs, cutting and finishing elements, etc. are excluded
from the guarantee.
Take the product to your retailer or an authorised service centre,
exhibiting proof of purchase.
The undersigned company
Via Lago Maggiore, 24
36015 SCHIO (VI) Italia
Declares under its own liability that the machine:
PRODUCT: Car polisher
MODEL/TYPE: LA3300
PRODUCT CODE: 1402082
Complies with the essential safety and health requirements of
Directives 2006/42 CEE, 2004/108 CEE, 2006/95CEE
SCHIO, 01.2010
An attorney
Mr. Bruno Anzolin
6