Adjusting The Backrest - Peg-Perego GT3 Instrucciones De Uso

the sack (arrow_c) and insert them in the most
appropriate loop (arrow_d), then re-attach the two
buckles on the rear of the backrest (arrow_e).
14 BRAKE: to brake the stroller, pull the handle on the
handlebar towards you (arrow_a); to release the brake,
disengage the lever (arrow_b). Always set the brake
when the stroller is not moving. To adjust the brake and
tighten it, unscrew the adjuster (fig_c) on the handlebar
to the outside. To loosen the brake, do the opposite.
15 ADJUSTABLE HANDLEBAR: the handlebar on the
stroller is height-adjustable. To adjust the height of the
handlebar, simultaneously press the side buttons (fig_a)
and block the handlebar in the desired position (fig_b).
16 ADJUSTING THE BACKREST: the backrest of the stroller
can be reclined to several positions. To lower the
backrest, lift the handle (arrow_a) as you recline the
backrest (arrow_b), locking it at the desired position.
To raise it, push the backrest up.
17 ADJUSTING THE FOOTREST: the footrest can be
adjusted to two positions. To lower the footrest,
pull the two side levers downwards (fig_a) while
lowering the footrest (fig_b). To raise the footrest, lift
it upwards until it clicks into place.
18 FRONT BAR: the practical front bar opens and closes
to make it easier for the child to get in and out of the
stroller when he/she is older.
To open the front bar, press the button located under
the armrest (arrow_a) and pull the front bar outwards
at the same time (arrow_b). To close the front bar, do
the opposite. The front bar can be removed. The front
bar is also extendible – to extend the front bar, press
the long button located under the armrest (arrow_c)
and pull the front bar outwards (arrow_d). To shorten
the front bar, press the long button and push the
front bar into the armrest.
19 SIDE CUP HOLDERS: the stroller is equipped with
two side cup holders that fold away or pull out as
necessary. To pull the cup holder out, turn the upper
part upwards (arrow_a) and lower the bottom part
(arrow_b). Turn the disk outwards (arrow_c) and
place your drink in the holder (fig_d) To close the cup
holder, do the opposite.
20 RAIN CANOPY: fit the rain canopy onto the stroller
and button it on the side to the hood (fig_a), button
the two sides of the rain canopy elastic to the bottom
of the front frames (fig_b).
21 The practical rain canopy can be lowered and remains
attached to the stroller through the buttons.
22 POUCH: place the pouch near its own housings,
located on the handlebar, and fasten it (fig_a). The
pouch can be worn as an accessory using the special
belt (fig_b).
23 SWIVELING OR STATIONARY FRONT WHEEL: to set the
front wheel on stationary, turn the knob to the closed
padlock (fig_a). To swivel the front wheel, turn to the
open padlock (fig_b).
24 AIR PUMP: to inflate the tires, use the pump located
under the seat (fig_a). Slip the hose off the pump
(fig_b) and screw it onto the opposite end of the
pump (fig_c). Remove the cap from the tire (fig_d)
and fasten the end of the pump hose (fig_e).
_ Before using the stroller for the first time, you are advised
to inflate the tires to a pressure of 25 P.S.I./1.7 bar.
25 SHOCK ABSORBERS: all the wheels are equipped with
shock absorbers. The rear wheels have adjustable
shock absorbers. You can choose from "HARD" for
soft terrain, such as sand and lawns, "SOFT" for rough
surfaces, such as gravel and cobble stones, and
"MEDIUM" for smooth, firm surfaces. To adjust the
shocks on the rear wheels, turn the knob to choose
one of the three settings. It is recommended to adjust
both rear wheels to the same setting.
GANCIOMATIC SYSTEM
Ganciomatic is a quick, practical system that allows
you to attach the Navetta XL and Primo Viaggio car
seat (available separately) to the stroller with the
Ganciomatic connectors.
26 GANCIOMATIC CONNECTORS ON THE STROLLER: To
raise the Ganciomatic connectors on the stroller, lift
the fabric covering in the corners of the seat. Raise the
two Ganciomatic connectors, which will automatically
move outwards.
_ To lower the connectors, do the opposite.
The Navetta XL and Primo Viaggio car seat can
be attached to the GT3 in stroller mode, with the
backrest attached, or in GT3 Naked mode (chassis
version).
To convert the GT3 into a chassis version GT3 Naked:
27 Put the backrest in the second position and remove
both of the side ridges that are holding it up (fig_a).
Hold down both of the buttons at the bottom of the
backrest (fig_b) and lift it up (fig_c). Before you attach
the Navetta XL or Primo Viaggio car seat, raise the rear
part of the Ganciomatic base (fig_d).
_ To convert the chassis back into a stroller, go through
the same steps in reverse order.
28 (fig_a) GT3 + PRIMO VIAGGIO
To attach the car seat to the stroller or chassis:
_ Apply the brakes on the stroller.
_ Raise the Ganciomatic connectors on the stroller.
_ Put the front bar in the first position.
_ If they are attached, remove the hood from the
stroller and completely lower the backrest.
_ Position the car seat so that it is facing the person
pushing and push it down until it clicks.
_ To remove the car seat from the stroller, consult the
instruction manual for the car seat.
(fig_b) GT3 + NAVETTA XL
To attach the Navetta XL bassinet unit to the stroller
or chassis:
_ Apply the brakes on the stroller.
_ Raise the Ganciomatic connectors.
_ Raise the leg rest on the stroller or chassis to the
highest position.
_ Remove the front bar.
_ If they are attached, remove the hood from the
stroller and completely lower the backrest.
_ Place the Navetta XL on the Ganciomatic connectors
of the stroller, with the head end of the bassinet unit
on the opposite side to the handle of the stroller.
_ Press on the sides of the Navetta XL with both hands
until it clicks into place.
_ To remove the Navetta XL from the stroller, consult
the instruction manual for the bassinet unit.
29 REMOVING THE WHEELS: to remove the rear wheels
press the button (arrow_a) and pull the wheels off
the sides of the stroller (arrow_b). To remove the front
wheel, press the button on the rear ledge (arrow_c)
and pull the wheel off (arrow_d).
30 FOLDING UP: before folding up the stroller, set the
front wheels to stationary. If the hood is mounted,
loosen the braces. To fold the stroller up, press button
number 1 (fig_a) using your right hand. Using your
left hand, grab the handle, press button number 2
(fig_b) and lift up the handle (fig_c). To complete the
folding, turn and fasten the safety hook (fig_d).
31 REMOVABLE SEAT COVER: unbutton the sack from the
seat (fig_a) and slip the sack off the footrest (fig_b).
Detach the sack from the armrests (fig_c).
32 Pull the leg divider strap up from under the seat (fig_a),
- 19 -