Publicidad
Idiomas disponibles
Idiomas disponibles
ENG
Instruction Manual EASYLITE
1.
Use as directed:
This product serves exclusively lighting purposes and may:
only be used with a voltage of 230V ~50Hz.
not be exposed to strong mechanical loads or to strong
contamination.
only be installed and operated after a condition inspection if the
product is dirty or has been moistened through storage.
not be modified or converted.
If these points named above are not adhered to, a short circuit or
electrical shock may occur!
2.
Technical Data:
230525
230535
Operating voltage:
230V ~50Hz
Safety class:
Safety type:
IP44
Bulb:
QPAR51,GU10, max. 50W
Dimensions
20/10 cm
86/ 10
(H/Head-Ø):
Swivel range:
160°
Weight:
0,65 kg
1,05 kg
Importer:
SLV Elektronik GmbH
IP 43: Protection against foreign objects > Ø 1,0mm - Protection against
spraying water up to 60° to the vertical.
IP 44: Protection against foreign objects > Ø 1,0mm - Protection against
splashing water from all directions.
3.
Installation
The electric connection may be executed only by an electric expert
who is familiar with the valid directives!
Attention: Switch off the power of the mains supply line or
respectively of the connection lead before doing any works
Use only parts, which are supplied with the product or are described as
accessories! Otherwise the product or the installation might not be
sufficiently safe.
Installation place:
SPOT/ DISPLAY: The product is suited for wall, ceiling and floor
installation. SPIKE: only floor installation.
Make sure that the product is mounted on a stable, even and tilt-fixed
background.
The light exit should be placed at least so far from the illuminated surface,
as indicated as minimum distance on the type plate of the luminaire:
. Pay special caution to easily inflammable objects (e.g.
foliage).
Separate Installation Steps
SPOT/ DISPLAY
Remove the mounting plate from the base of the lamp (1).
Determine the place of installation and mark the holes to be drilled. Note
that the cable outlet of the power supply line fits between the mounting
bracket and the canopy. Do not damage the power supply line, e.g. by
drilling, screws or strong bending.
Electrical Connection
The product must be able to be separated by an all pole separation from
the current supply.
Direct the connection lead through the cable screwing (2).
Secure the cable screwing.
For electric connection attach the black or brown wire (live conductor) of
the mains supply with the clamp L and the blue wire (neutral conductor)
of the mains supply with the clamp N. The green-yellow wire (protective
conductor) of the mains supply has to be tightly screwed into the earth
clamp
Now fasten the basis back on the mounting plate.
Applying the earth spike: Screw the spike on the bottom of the lamp
(3a).
Fasten the lamp to the mounting surface (3b).
Ensure that the light fixture holds securely!
SPIKE
Place the product on a suitable place. Connect the plug with a suitable
outdoor socket (i.e. SLV art-no. 227000).
Inserting the bulb: Loosen the two screws on the font of the lamphead.
Carefully take off the front part and the glass. Take care that the glass does
not fall down. Insert the bulb with a quarter-turn to the right. Put the glass
and the front part of the lamphead back on.
Adjust the direction of the lamp head by loosening the adjustment
screw(A).
230545
The product is now ready for operation.
I
IP43
45,5/ 10
0,75 kg
.
4.
Operation
Information for the user:
Operate the product only if it is working correctly. Switch off the product
with a malfunction immediately and operate it again only after examination
by an electrical specialist. This is the case, when:
visible damages appear.
the product does not work.
smoke, steam or crackling sounds appear.
an overheating is recognisable.
Repairs of the product or work on mains voltage-prominent sections may
only be carried out by qualified electricians.
Attention: Here exists mortal danger from an electric shock!
How to avoid failure and fire risk:
Do not cover the product - provide free air circulation!
Do not hang or fasten anything on the product, especially no decoration.
of the product.
:
Replace damaged protection glasses immediately!
Never let children play unsupervised with electric products! Children
can not always estimate dangers in dealing with electric energy correctly.
The following enviromental influences may have unwanted effects on
the surface of the product:
acid rain and sour soil
high salt content in the air
thawing salt
cleaning agents
other chemical substances (e.g. herbicides)
Protect the product by adequate means to avoid unwanted changes of the
surface. Cleaning tip: Switch off power! Clean the product with a damp
cloth.
What is to do if a bulb is defect or does not work?
Disconnect the product from power, before you exchange the bulbs.
Caution: Let the bulb cool down first before replacement – otherwise
considerable risk of injury exists because of the hot surface.
Replace the bulbs only with bulbs of the same data like socket, power
and capacity. Every other sort of bulb can lead to damages of the light.
Replacing the bulb: see Installation.
5.
What else has to be considered?
Disconnect the product from power, before you...
clean or maintain the product.
do any works on the product or its components (electric expert).
© by SLV Elektronik GmbH
230525/35/45
08/2008
Technical Details are subject to change.
Duplication prohibited !
Publicidad
