Function Settings - Mitsubishi Electric Mr.SLIM PEAD-M35JA Manual De Instalación

8. Electrical work
2. Setting example
(1) To use the units in the same room
[Fig. 8-4-3] (P.8)
a Separate setting
Assign a different pair number to each indoor unit to operate each indoor unit
by its own wireless remote controller.
[Fig. 8-4-4] (P.8)
b Single setting
Assign the same pair number to all the indoor units to operate all the indoor
units by a single wireless remote controller.
[Fig. 8-4-5] (P.8)
(2) To use the units in different rooms
Assign the same pair number to the wireless remote controller as that of the
indoor unit. (Leave the setting as it is at purchase.)
2) Setting the Model No.
a Insert batteries.
b Press the SET button with something sharp at the end.
blinke and Model No. lighted.
MODEL SELECT
c Press the temp button to set the Model No.
d Press the SET button with something sharp at the end.
and Model No. are lighted for three seconds, then turned off.
MODEL SELECT
Indoor Unit Model
PEAD

8.5. Function settings

8.5.1. For wired remote controller
a (Fig. 8-5-1)
• Select "Service" from the Main menu, and press the [SELECT] button.
• Select "Function setting" with the [F1] or [F2] button, and press the [SELECT]
button.
b (Fig. 8-5-2)
• Set the indoor unit refrigerant addresses and unit numbers with the [F1] through
[F4] buttons, and then press the [SELECT] button to confirm the current setting.
<Checking the Indoor unit No.>
When the [SELECT] button is pressed, the target indoor unit will start fan
operation. If the unit is common or when running all units, all indoor units for the
selected refrigerant address will start fan operation.
c (Fig. 8-5-3)
• When data collection from the indoor units is completed, the current settings
appears highlighted. Non-highlighted items indicate that no function settings are
made. Screen appearance varies depending on the "Unit No." setting.
d (Fig. 8-5-4)
• Use the [F1] or [F2] button to move the cursor to select the mode number, and
change the setting number with the [F3] or [F4] button.
e (Fig. 8-5-5)
• When the settings are completed, press the [SELECT] button to send the setting
data from the remote controller to the indoor units.
• When the transmission is successfully completed, the screen will return to the
Function setting screen.
8.5.2. For wireless remote controller
[Fig. 8-5-6] (P.9)
A Hour button
B Minute button
C TEMP button
D TEMP button
E ON/OFF button
F CHECK button
1. Changing the external static pressure setting.
• Be sure to change the external static pressure setting depending on the duct and
the grill used.
a Go to the function select mode
Press the CHECK button F twice continuously.
(Start this operation from the status of remote controller display turned off.)
CHECK
Press the TEMP button C once to set "50". Direct the wireless remote controller
toward the receiver of the indoor unit and press the Hour button A.
b Setting the unit number
Press the TEMP button C and D to set the unit number to 01-04 or AL. Direct the
wireless remote controller toward the receiver of the indoor unit and press the
Minute button B.
c Selecting a mode
Enter 08 to change the external static pressure setting using the C and D
buttons.
Model No.
Direct the wireless remote controller toward the receiver of the indoor unit and
026
press the Hour button A.
d Selecting the setting number
Use the C and D buttons to change the external static pressure setting to be
used.
Direct the wireless remote controller toward the sensor of the indoor unit and
press the Hour button A.
e To set the external static pressure
Repeat steps c and d to set the mode number to 10.
f Complete function selection
Direct the wireless remote controller toward the sensor of the indoor unit and
press the ON/OFF button E.
Note:
• Whenever changes are made to the function settings after installation or
maintenance, be sure to record the changes with a mark in the "Setting"
column of the Function table.
8.5.3. Changing the power voltage setting (Function table 1)
• Be sure to change the power voltage setting depending on the voltage used.
is lighted and "00" blinks.
Current setting number: 1 = 1 beep (one second)
2 = 2 beeps (one second each)
3 = 3 beeps (one second each)
19