Publicidad
Idiomas disponibles
Idiomas disponibles
connection must be made according to the Sta
manufacturer declines all responsibility for inju
stallation.
in
6 – Technical characteristics
The unit is supplied together with a plastic bag containing this instruction manual that must be retained. The manual contains
technical details, electrical diagrams and tables regarding the unit.
The technical details of the unit are also provided on the serial number plate (FIG. 9 page 4) which specifies:
1. Commercial name of the refrigeration unit
2. Code corresponding to the refrigeration unit
3
. Refrigeration unit serial number
4. Supply voltage
5. Frequency
6. Maximum absorbed power
7. Maximum absorbed power during defrosting
8
. Standard lighting power
9. Working display surfac
10. Working load
11. Type of refrigerant gas used to operate the system
12. Quantity of refrigerant gas with which each individual system is filled
13. Environmental climatic class and reference temperature (dry bulb temperature)
14. Class of refrigeration unit according to the product preservation temperature
15. Protection class of the electrical system
16. Order number under which the refrigeration unit was built
17. Order number under which the refrigeration unit was put into production
18. Year in which the refrigeration unit was produced
Warning: Neither the registration plate nor the warning labels must be removed under any circumstance. The ma
declines all responsibility if this warning is not followed.
It is declared that the equipment complies with the Decree Law 25/01/1992 N. 108 in accordance with CE Directive 89/109
concerning materials and objects destined to come into contact with foodstuffs.
7
– Filling with products and use of the cabinet (startup))
If the island has been set at a sharp angle duri
lubricating oil to collect in the compressor. If this instruction is not followed the motor-driven condense
beyond repair. Any swelling of the unit while working does not compromise its proper functioning.
The island may only be started up for the first time when points 3 and 4 have been completed.
With the island turned off, proceed as follows: remove the protective plastic film on the outside and then clean the unit,
following the instructions given in point 10.
Fit the plug in the socket (with the characteristics described in point 5) and operate any remote-control switch that may have
been fitted. A slight operating noise made by the motor and the display turned on indicate that the unit has been switched on.
The display (page 4, FIG. 10) located on the front panel indicates the operating temperature of the island. The instruction
booklet of the electronic controls, to which the display refers, is enclosed with the instruction manual (this device cannot be
mpered with due to a safety password that only a specialized technician can change).
ta
The unit starts its cooling c
the display is – 18°C for frozen packed foods and – 20°C for ice cream.
The unit has been designed to display packed foodstuffs, it must maintain the temperature of the product and must not lower
it, and consequently, the product must only be placed inside the unit if it is already refrigerated and is at its respective
preservation temperature.
Bottles and glass containers or jars full of liquid must not be stored in the BT versions as they may burst.
For a correct preservation of the product, it is advisable:
-
Never exceed the maximum load line shown on the inside of the island (page 4, FIG. 11):
- maximum load line = 55 cm by climatic class 3 (25°C RH 60%)
- maximum load line = 50 cm by climatic class 4 (30°C RH 55%)
When an island that is already partially loaded with goods is filled with more products (apart from adhering to the
-
points referred to above), it is good practice to place the new foodstuffs under the existing ones.
-
Each unit is equipped with sliding covers in low-emissivity glass. These are necessary for the proper working, they
must be kept closed (page 4, FIG. 12) and they can be opened on
The plug-in islands are provided, as a standard fitting, with an electronic control. The thermostat adjustment and the amount
of gas are set in the factory and any tampering with these settings will relieve the manufacturer of all responsibility.
8 – Prohibitions and prescriptions
Warning: disconnect the cabinet from the power supply in case it is not used for long time. The power supply has to be
disconnected by the remote-control switch fitted upstream from the power socket.
e
ng positioning, wait at least three hours before starting it up to allow the
ycle after it has been switched on. The product can be loaded when the temperature shown on
ndards in force. It is a
ry to people or dama
ly to fill up and take out the products.
bsolutely forbidden to use adapter plugs. The
ge to objects caused as a result of improper
nufacturer
r may be damaged
15
Publicidad
