Wireless Regulatory Information; Fcc Radiation Exposure Statement; Industry Canada Radiation Exposure Statement - Linksys RE6500 Guia Del Usuario

Wireless Regulatory Information

Wireless Regulatory Information
FCC Statement
This device complies with Part 15 of the FCC Rules .
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation .
This product has been tested and complies with the
specifications for a Class B digital device, pursuant to
Part 15 of the FCC Rules . These limits are designed
to provide reasonable protection against harmful
interference in a residential installation . This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used according to the
instructions, may cause harmful interference to radio
communications . However, there is no guarantee that
interference will not occur in a particular installation . If
this equipment does cause harmful interference to radio
or television reception, which is found by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and
devices
• Connect the equipment to an outlet other than the
receiver's
• Consult a dealer or an experienced radio/TV technician
for assistance
FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could
void the user's authority to operate this equipment .
IEEE 802 .11b or 802 .11g operation of this product in
the USA is firmware-limited to channels 1 through 11 .
The device for the band 5150-5250 MHz is only
for indoor usage to reduce the potential for harmful
interference to co-channel mobile satellite systems .

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment . This
equipment should be
with minimum distance 2
and your body .
This device and it's antennas(s) must not be co-located
or operating in conjunction with any other antenna
or transmitter except in accordance with FCC multi-
transmitter product procedures .
Industry Canada Statement
CAN ICES-3 (B)/NMB-3 (B)
installed and operated
0
cm between the radiator
This device complies with Industry Canada license-
exempt RSS standard(s) . Operation is subject to the
following two conditions: (1) this device may not cause
interference, and (2) this device must accept any
interference, including interference that may cause
undesired operation of the device .
For product available in the USA/Canada market, only
channel 1~11 can be operated . Selection of other
channels is not possible .
The device could automatically discontinue transmission
in case of absence of information to transmit, or
operational failure . Note that this is not intended to
prohibit transmission of control or signaling information
or the use of repetitive codes where required by the
technology .
Industry Canada Radiation Exposure
Statement
This equipment complies with IC radiation exposure limits
set forth for an uncontrolled environment . This equipment
should be installed and operated with minimum
distance cm between the radiator & your body .
20
This device and it's antennas(s) must not be co-located
or operating in conjunction with any other antenna
or transmitter except in accordance with IC multi-
transmitter product procedures .
Restrictions in the 5 GHz Band
The device for the band 5150-5250 MHz is only for
indoor usage to reduce potential for harmful interference
to co-channel mobile satellite systems .
This device has been
antenna having a maximum gain of 3.
2 .4 GHz and 5 GHz respectively . Antenna having a higher gain
is strictly prohibited per regulations of Industry Canada .
The required antenna impedance is 50 ohms .
The maximum antenna gain (Please see the table below)
permitted (for devices in the bands 5250-5350 MHz
and 5470-5725 MHz) to comply with the EIRP limit and
because high power radars are allocated as primary users
(meaning they have priority) in 5250-5350 MHz and
5650-5850 MHz, these radars could cause interference
and/or damage to license exempt LAN devices .
For 2.4
Antenna
No. GHz Gain
Type
(dBi)
1 Dipole
3.50
2 Dipole 3.50
designed to operate with
5 5
dBi and 3.
For 5 GHz Gain Antenna
(dBi) Connector
Band 1: 3.50
R-SMA
Band 4:
3.50
Band 1: 3.50
R-SMA
Band 4:
3.50
1
an
dBi at