Giordani evolution isofix Manual Del Propietário página 15

G E I
UK
IORdANI vOLuTION sOfIx
sECuRING YOu BABY
Securing your baby using the baby insert
1. CAUTION For the protection of your
baby. Please use the baby insert at-
tached to this car seat when your baby's
weight is less than 15kg. The baby insert
is used to provide extra comfort for very
small babies, and it gives your baby the
necessary support while he or she is
still small.
• Always secure your baby in the car
seat using the harness.
• Never leave your baby unattended in
the car seat when placing it on elevated
surfaces (e.g. a table, nappy changing
unit, etc.).
• Never allow the strap end to become
caught in moving parts (e.g. automatic
doors, escalators, etc.).
Caution!
• The plastic parts of the car
seat heat up in the sun, so that your
baby may get burnt. Protect your baby
and the car seat against intensive solar
radiation (e.g. by putting a light cloth
over the seat).
• Take your baby out of the car seat as
often as possible to relieve its spine.
We recommend frequent breaks dur-
ing long journeys. Even outside of
the car, please avoid leaving your
baby in the car seat for too long.
How to adjust the belts, headrest and seat
positions
IMPORTANT The correct belt height of the
shoulder belts is attained when the belt
disappears into the shell slightly above the
shoulder of the child. Make sure that the
shoulder belts fit properly over the shoulders
of the child.
1/2/3
CAR SEAT
(9 MONHS - 11 YEARS, APPROXIMATELY)
Adjusting the belts
2. Loosen the harness straps by pressing
the release button and pulling the har-
ness straps as far as you can.
Note! Do not pull the Shoulder pads.
Nine heights of the headrest
3. The headrest can be set at five differ-
ent heights in group 1 mode with the
shoulder belts axle in place. There are
four additional positions in Group 2 & 3
mode once the shoulder belts axle and
harness straps has been taken off.
4. Press the button on the Headrest han-
dle on the top of the seat. It is important
to make sure the headrest fit properly to
head.
Recline Positions of the Car Seat
5. The car seat can be used in 5 Recline
positions:
Lift the Recline adjustment handle under
the front of the seat up and pull or push
the shell forwards or backwards. Release
the handle in the required position and
push until you hear a distinct click.
Securing your baby using the harness
6. Loose the harness straps by pressing
the release button and pulling the har-
ness straps as far as you can.
Note! Do not
pull the shoulder pads.
7.
Open the harness buckle, then fix the
harness straps into the belt guide band.
Put the baby into the car seat.
8. The correct height of the shoulder belts
is attained when the belt disappears into
the shell slightly above the shoulder of
the child. Make sure that the harness
straps fit properly over the shoulders of
the child.
28
9.
Slide buckle tongues together and insert
them in the buckle with an audible sound
"click".
10. Pull the straps tight by the harness ad-
justment strap, and make sure the tight-
ness is comfortable to your kid.
CAUTION Do not twist or interchange
the harness straps.
Tightening the harness
11. CAUTION Pull the strap end straight to-
wards you, not upwards or downwards.
Please pay attention to the strap end.
Whilst traveling (especially outside the
car) it should always be attached to the
cover.
Checklist to ensure that your baby is
buckle up correctly.
12. IMPORTANT For the safety of your baby,
please check that...
• The harness straps of the car seat are
comfortable but firm fit around your
child.
• The harness straps are adjusted cor-
rectly.
• The harness straps are not twisted.
• The buckle tongues are engaged in the
harness buckle.
INsTALLATION IN THE vEHICLE
Please do not leave your child unattended
in the child safety seat in the vehicle.
For the protection of all vehicle occupants:
In the case of an emergency stop or an ac-
cident unsecured persons or
objects may cause injury to other vehicle oc-
cupants. Please always
check that...
• The backrests of the vehicle seats are
locked (i.e.that a foldable rear seat bench
latch is engaged).
• All heavy or sharp-edged objects in the
vehicle(e.g. on the parcel shelf) are secured.
• All persons in the vehicle have their seat
belts fastened.
• The child safety seat is always secured
when it is in the vehicle, even if no child is
being transported.
To protect your vehicle
Some vehicle seat covers of sensitive
materials(e.g. velour, leather, etc.) may de-
velop wear marks when child seats are used.
This can be avoided by placing a blanket or
towel under the child seat.
Installation of Group I for the children
whose weight between 9-18kg with
ISOFIX and Top tether.
IMPORTANT First please check if there
are 2 ISOFIX anchorings in the perpen-
dicular intersection of the vehicle seat
back and seat cushion, and the user-
ready top tether anchoring behind the
vehicle seat.
Tips: The user-ready tether anchorage
usually permanently installed on the in-
ner rear luggage shelf or on the vehicle
floor. Details you could read your vehicle
guidelines or contact the vehicle manu-
facturer.
13. Press the Release button to release
the ISOFIX connectors.
14. Push the ISOFIX connectors directly
into the anchorages until you hear an
audible sound "click".
15. Tip: If the ISOFIX connectors are cor-
rectly installed, the Release button
will pop out, and you can see a clear
green mark on it.
16. Grasp the seat body to check the seat
if it is fastened tightly or shakes. If the
seat shakes and the ISOFIX connec-
tors are pulled out, please repeat the
29