stayer SC210BW Manual De Instrucciones página 31

Changing brushes
Warning!
Always use the brushes as supplied by the official technical
service.
1.Remove screw 48.
2.Remove lid 47.
3.Remove screw 50.
4.Move pressing spring 51 to the left.
5.Extract used 52 brush from the brush holder 49.
6.Insert new brush into the brush holder 49.
7.Place pressing spring 51 over the brush.
8.After applying the brush connector tighten screw 50.
9.Position lid 47.
10.Tighten screw 48.
Greasing
This machine does not require any specific greasing by
the user. Specific greasing of the electrical tool will be
carried out on the occasion of the regular maintenance
revisions at the official technical service.
19.Repair service of the manufacturer or
commercial agent:
Calle Sierra de Cazorla, 7
Área Empresarial Andalucía - Sector 1
28320 PINTO (MADRID)
20.List of parts that may be replaced by the
user
IMAGES Y Z
1.Cutting disk 21.
2.Lower stationary guard 34.
3.Movable guard 26.
4.Brushes 52.
5.Guides for adjusting the cutting depth at the lower table
41 .
6.Guides for adjusting the cutting depth at the lower table
27.
21.Special tools as possibly required
Tools as required are standard or included with the
accessories of the machine.
22. Safe operation
1.Keep working area clean. Unorderly working areas
and benches are susceptible of causing damages.
2.Take into account the surroundings of the working
area. Do not expose tools to rain. Do not use tools at humid
or wet locations. Keep working area well illuminated. Do
not use tools in the presence of inflammable liquids or
gases.
3.Protect against electrical shocks. Avoid contacts of
the body with earthed or chassis-earthed surfaces (e.g.
pipes, radiators, heaters, refrigerators, etc.).
4.Keep other persons away. Do not allow that other
persons, especially children, who are not linked to the
ENGLISH
31
work, touch the tool or extensible cables, and keep them
away form the working area.
5.Store tools that are not being used. When not in use,
tools should be stored at a dry and closed location out of
the reach of children. Do not place anything on top of the
machine, or store the machine start backwards.
6.Do not force the tool. The tool operated better and
safer at the assigned characteristic for which it has been
designed.
7.Choose the right tool. Do not force a small tool to carry
out the work that corresponds to a heavy tool. Do not use
tools for purposes for which they have not been designed;
for instance, do not use circular saws for cutting the trunks
of trees or the branches thereof.
8.Dress suitably. Do not use loose-fitting garment or
jewellery articles that may get caught by moving parts.
The use of nonslip footwear is recommended for working
at outside locations. For long hair use protective caps.
9.Use safety equipment. Use protective goggles.
Use face protector or mask to avoid dust if the cutting
operations may generate it.
10.Connect the dust-extraction equipment. Should
devices for the connection thereof to dust extraction and
collection equipments be provided, make sure that they
are in fact connected and adequately used.
11.Do not mistreat the cables. Never pull the cable to
disconnect it from the socket. Keep the cable away from
heat, oil and cutting edges.
12.Secure operations. When possible, use fastening
clasps or clamps for workbenches for fastening the
workpiece. This is safer than using your hands.
13.Do not excessively extend our radius of operation.
Always keep a firm stand on the ground and preserve your
equilibrium.
14.Service tools
sharpened and clean for a better and safer operation
thereof. Follow the instructions for greasing and the
changing of accessories. Periodically check extensible
cables and replace them if they are damaged. Keep grips
dry, clean and free of grease and oil.
15.Disconnect the tools. Disconnect tools form the
grid supply when not in use, before repairing and when
changing accessories such as saw blades, drilling bits
and blades.
16.Remove setting keys and adjustable spanners.
Make it your custom to check that setting keys and
adjustable spanners are removed from the tool before it
is operated.
17.Avoid unintentional starting. Make sure that the
switch is in the "open" position when plugging the machine
into the socket.
31
carefully. Keep cutting tools