Adjusting The Headrest Height - KikkaBoo TWISTER Instrucciones De Uso

HOW:
GROUP 0+ / Install rearward facing.
GROUP 1 / Install forward facing.
GROUP 2 / Install forward facing.
NOTICE:
The child seat must only be used in this seat IF it has a lap and diagonal belt (3 points).
3.
INSTALLING THE CAR SEAT GROUP 0+
NOTICE: GROUP 0+ only. 0 to 10 months (0-10 kg)
1. Check the seat is ready to be installed rearward facing (Group 0+) as shown in fig. 3.3. Recline the seat fully. Pull the lever (G) forward and adjust the angle
of recline to position 4 without releasing the lever. If it is necessary swivel the seat 180º to place the seat in the opposite direction of travel (fig. 3.2). Release
the lever when the seat is in the desired position.
2. By turning the Isoclick Fix arms, extract both arms (N) located in the base of the seat (fig. 3.3).
3. Place the seat in the back seat of the vehicle in the opposite direction of travel.
4. H old the safety seat with both hands and insert the two Isoclick Fix arms (N) firmly into the vehicle´s isofix anchoring points until they fasten with a click
on both sides. The red button will change to green on both sides (fig. 3.4).
5. S hake the seat to check that it is correctly anchored to the vehicle's ISOFIX points.
6. Pass the abdominal strap of the seat belt through the back support slots (K) as fig.3.5 shows. Buckle the vehicle seat belt until you hear a click.
7. T ake up the remaining slack of the diagonal section of the 3-point seat belt (fig. 3.6). and make sure it is as tight fitting as possible. Ensure the straps are
not twisted or knotted at any point.
Uninstalling the Isoclick Fix system
1. To free the Isoclick Fix anchoring, press the Isoclick Fix system unlock buttons, in order to free the seat from the vehicle ISOFIX anchoring system (fig. 6.7
and 6.8)
4.
PLACING THE CHILD IN THE SEAT GROUP 0+
Proper adjustment of the height of the harness ensures the child will be seated correctly. The harness should be adjusted to the height of the
child's shoulder or slightly above; never behind the child's back or level with the ears (fig. 4.1).
1. L oosen the harness straps by pulling them gently while pressing the harness adjustment button (E) (fig. 4.2). Tip: Only pull on the harness
straps. Not the shoulder pads.
2. R elease the buckle (D) to make it easier to seat the child (fig.4.3).
3. Place the child in the seat.
4. Secure the child in the harness by joining the two parts of the clasp and fastening the buckle (D) until you hear a click (fig. 4.4).
5. Gently pull the harness adjustment strap to achieve the correct tension (F) (fig. 4.5). Remember that in order to ensure the child's safety
the harnesses should fit tightly.
5.

ADJUSTING THE HEADREST HEIGHT

Proper adjustment of the height of the headrest ensures the child will be seated correctly. The headrest should be adjusted to ensure that the harness straps
(B) should be adjusted to the height of the child's shoulder or slightly above; never behind the child's back or level with the ears (fig. 4.1).
1. L oosen the harness straps (B) by pulling them gently while pressing the harness adjustment button (E) (fig. 5.1). Tip: Only pull on the harness straps. Not
the shoulder pads.
2. Adjust the headrest according to the child´s height by pulling the headrest height regulator (A) adjusting the harness to the height of the child´s shoulder
or slightly above (fig. 5.2).
6.
INSTALLING THE CAR SEAT. GROUP 1
NOTICE: GROUP 1 only from 9 months to 4 years approx. (9-18 kg)
2