Function Buttons - Klein Tools KTB5 Manual Del Usuario

Tabla de contenido

Idiomas disponibles

ENGLISH

UNITS

Press the UNITS button to display amps, watts, and watt-hours information for inputs and outputs. When using both USB and AC outputs, amps will only be display on the circuit

that was initially activated. To cycle to the amp output from the other port, the INFO (12) button must be pushed. The data provided is real-time and will adjust as the load changes

from the device that is plugged into the portable battery.

DISPLAY

Press the DISPLAY button to illuminate the LCD for short duration. Press and hold the DISPLAY button to keep LCD illuminated indefinitely. Press and hold the DISPLAY button

again to return to default mode.

INFO

Press the INFO button for details on battery performance level. Press button to cycle amps between USB and AC outputs, when both are in use.

BATTERY LEVEL

: The battery level is provided by percentage of battery charge corresponding to the number of bars and percentage displayed. The bars in the battery level

correspond to the current state of charge, 0-20%, 21-40%, 41-60%, 61-80%, and all five are lit when charge level is above 81%.

TIME UNTIL EMPTY/FULL

: Provides the user live telemetry data on time to completely charge, or deplete the battery based upon the energy entering or leaving the battery. Please

be aware that this value can adjust multiple times as the energy draw changes from the connected devices. This is evident during initial activation of ports with a connected device.

INPUT

: The KTB5 is capable of providing input energy in watts, watt-hr, or amps.

OUTPUT

: The display will only provide amp output of the AC port or the DC port, not a combined value. Refer to function button details on how to display amp output from

each port, if both are in use.

COOLING FAN

: KTB5 utilizes an internal cooling fan to ensure the product is operating within the appropriate temperature range. The unit, when it experiences a higher output

load, will automatically turn on the fan. During discharge, and possibly charging, the fan may operate intermittently to keep internal temperature within operating range. The fan will

likely start when the AC circuit is activated to ensure proper operation.

CHARGING KTB5

Only charge unit with provided AC wall charger, Klein Cat. No. 29201.

Charge unit indoors.

Connect the provided AC Wall Charger

LED

will be illuminated, and the LCD display will provide charge level

fully charge KTB5 every 3 months to maintain the health of the battery pack.

POWERING /

CHARGING DEVICES WITH KTB5

Select the type of outlet required by pressing the USB Output ON/OFF Button

is pressed to activate the port. When activated, the indicator on the button will illuminate green, indicating that the output(s) are active, and the LCD display will turn on and provide

details on the charging output. Press the ON/OFF button(s) to shut down the output(s) when not in use. The LCD will automatically shut down when no outputs are activated.

KTB5 will enter sleep mode after 90 seconds of inactivity (no output load detected), and will "wake up" when inputting a charging cord or when any button is pressed.

PASS-THROUGH CHARGING

The advanced battery management system of the KTB5 allows it to charge a connected device while the wall charger unit is plugged into the KTB5. The KTB5 is capable of

supporting more output than can be provided by the wall charger input. Therefore, the KTB5 may still be depleting battery capacity depending upon the load required by the

connected device being charged.

OVERLOAD CONDITION

If the LCD displays the overload condition symbol ("OL"); do the following:

• Turn off USB ports

and AC outlets

• Disconnect all devices, including the KTB5's charging cord.

• Verify the maximum power requirements for all devices, and confirm that the device power requirements do not exceed KTB5's capacity (see GENERAL SPECIFICATIONS).

• Reconnect only necessary devices.

• Turn on USB ports and/or AC outlets and resume operation.

If an overload condition occurs on the input port, the portable battery will automatically shut off the input port. The port will be reactivated when the input source meets the

specification outlined in the GENERAL SPECIFICATIONS section. Only charge the unit with provided AC wall charger.

KLEIN TOOLS ACCESSORY MOUNT

To attach a Klein Tools accessory to KTB5, such as the AEPJS1 Wireless Jobsite Speaker, or 55437 Tradesman Pro

with the slots on KTB5's Accessory Mount, then insert and rotate clockwise to lock into place. To remove the accessory, rotate counterclockwise and pull out.

DETAILS DISPLAYED ON LCD

OPERATING INSTRUCTIONS

to the AC Charger input

, and allow KTB5 to fully charge prior to use, approx. 9 hours. When charging, the AC Charging Indicator

. The green indicator light will no longer be illuminated when the ports / outlets are turned off.