Synchronising V2 Rolling Code Remote Con- Trols - JMA M-FR1 Manual De Instrucciones

1. Press and hold the up and down buttons on the Telis remote
control for 2 seconds. The red LED on the receiver will remain
lit.
Keytis remote control
2. Press the button of the device to be synchronised. The LED
on the receiver will flash.
3. Wait until the LED turns off.
Telis 1RTS remote control
2. Press the rear button on the remote control for half a second.
The LED on the receiver will flash.
3. Wait until the LED turns off.
Telis 4 RTS remote control
2. Press the channel selection button until the LED for the desi-
red channel lights up.
3. Press the rear button on the remote control for half a second.
The LED on the receiver will flash.
4. Wait until the LED turns off.
SYNCHRONISING SOMMER ROLLING CODE REMOTE
CONTROLS
SOMMER remote control can only be synchronised directly on
the receiver.
Direct synchronisation procedure on the receiver
1. Press button B on the receiver
a. Once for channel 1. LED (C1) will light up.
b. Twice for channel 2. LED (C2) will light up.
The receiver will exit synchronisation mode if no code is trans-
mitted during a period of 10 seconds.
To exit synchronisation mode, press key B several times until
all LEDs have turned off.
2. Press the desired button (D) on the remote control. The trans-
mitter will send the radio code to the receiver.
The LED for the selected channel will flash and switch off.
Repeat Steps 1 and 2 to synchronise additional transmitters
with this receiver.
SYNCHRONISING TELCOMA FM ROLLING CODE REMO-
TE CONTROLS
TELCOMA FM remote controls can be synchronised either di-
rectly on the receiver or remotely using a remote control alre-
ady synchronised with the receiver.
Remote synchronisation procedure
This procedure requires at least one four-channel remote con-
trol with the previous system already synchronised with the
receiver.
1. Press the 4 buttons on the remote control already synchroni-
sed with the receiver simultaneously for 3 seconds.
2. Release, and within 2 seconds briefly press, on the same
original device, the button that the receiver has already syn-
chronised.
3. Within 2 seconds press the button of the remote control you
wish to synchronise.
4. Repeat the process for the remaining buttons if necessary.
Direct synchronisation procedure on the receiver
1. On the receiver, press the P button associated with the chan-
nel to be synchronised with the remote control.
2. The LED will flash 5 times.
30
3. While the LED is flashing press the button on the remote
control associated with the code to be synchronised.
4. If synchronisation is successful, the LED will emit a long
flash.
5. Repeat the operation for all other remote controls you wish
to synchronise.
SYNCHRONISING V2 ROLLING CODE REMOTE CON-
TROLS
V2 remote controls can be synchronised either remotely or di-
rectly on the receiver.
Remote synchronising procedure
1. Press buttons 1 and 2 on the remote control to be synchroni-
sed simultaneously for approximately 10 seconds.
2. Release.
3. Within 5 seconds, press any other button on the device to
be synchronised.
4. The receiver LED will turn off after a few seconds, indicating
that the unit has exited synchronisation mode.
The code has been stored.
Since this option is not enabled on all models we recommend
the following procedure.
Direct synchronisation procedure on the receiver
1. Open the receiver and locate the small SW1 button.
2. Press until the receiver LED lights up.
3. Within 5 seconds, press the button on the remote control to
be synchronised and hold until the receiver LED blinks.
4. The receiver LED will turn off after a few seconds, indicating
that the unit has exited synchronisation mode.
The code has been stored.
Observations
If the procedure fails, it may mean that the receiver memory is
full and impedes synchronisation of new devices without the
installer's permission.
SYNCHRONISING THE PUJOL VARIO ROLLING CODE RE-
MOTE CONTROLS
PUJOL VARIO rolling code remote controls are synchronised
using the same procedure as for JMC devices.
There are 3 synchronisation procedures for these devices.
PIN-MODE remote synchronising procedure
The following procedure must be applied if the receiver bears
the words PIN-MODE:
1. Stand near the receiver and use a pointed object to press
the pushbutton at the rear of the remote control you wish to
synchronise.
The receiver will emit a long beep, indicating that the device
has been successfully synchronised.
Remote synchronisation procedure using the original remote
control
1. Stand near the receiver and use a pointed object to press
the pushbutton at the rear of the synchronised remote control.
The receiver will emit a beep, indicating that it has switched to
synchronisation mode.
2. Within 10 seconds of the beep, press the button on the devi-
ce to be synchronised.
The receiver will emit another short beep to indicate that the