Trolley Instructions For Low Headroom - Wayne Dalton 9100 Instrucciones De Instalación Y Manual Del Propietario

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Trolley Installation for
Determine center line of door. Mark vertical line at this
point, on the header wall. Raise the door slightly until the
top section reaches the highest point of travel (high
Using a level, mark this high arc point of travel on the header
wall, intersecting the vertical center line, as shown in FIG.
3.1 through 3.2.
Hold the wall bracket's bottom edge to the
appropriate 1/2" - 1" (room permitting) above of the high
arc line and centered on the vertical
3.2. Spot the wall brackets mounting holes on the header
wall and then refer to your
garage door operator manual for
pre-drilling and securing the
wall bracket to header.
OPERATOR HOOK-UP CHARTS, refer to referenced illustrations
in FIG. 3.3 through FIG. 3.4 for correct arm hook-up from
trolley to operator bracket.
NOTE: Refer to your operator manual for specifi c details on
how to assembly the curved and straight arm, as shown in
FIG. 3.3 through FIG. 3.4.
NOTE: Depending on your setup, you may or may not have to
cut straight arm to accomplish trolley settings, as shown in
FIG. 3.3 through FIG. 3.4.
Attach door arm to trolley and align the appropriate door arm
hole with the hole in the door operator bracket. Insert (1) hex
head bolt through hole of operator bracket and door arm.
Install (1) LOCKING hex nut and just tighten until snug.
WARNING
FAILURE TO USE LOCKING NUT CAN RESULT IN ARM RE-
LEASING AND POSSIBLE RESULTING IN PROPERTY DAMAGE
AND/OR PERSONAL INJURY.
QUANTUM AND CLASSIC OPERATORS REQUIRE:
(1) 3/8" - 16 x 1" hex bolt and (1) 3/8" - 16 LOCKING hex nut,
as shown in FIG. 3.5.
LINEAR, LIFTMASTER (SEARS), GENIE OPERATORS
REQUIRE:
(1) 5/16" - 18 x 1" hex bolt and (1) 5/16" - 18 LOCKING hex
nut, as shown in FIG. 3.5.
Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your
local yellow pages/business listings or go to the Find a Dealer section online at www.wayne-dalton.com
Low Headroom
arc).
line, as shown in FIG.
Using the
LEVEL
HIGH ARC
TOP
LOW
SECTION
HEADROOM
TRACK
FIG. 3.1
STRAIGHT
ARM
FIG. 3.3
LOCKING
HEX NUT
STRAIGHT ARM
SHOWN
FIG. 3.5
OPERATOR HOOK-UP CHART FOR LOW HEADROOM
OPERATOR MODELS
PREFERRED
REF. ILLUSTRA-
HOOKUP
TIONS ABOVE
CURVED /
QUANTUM/CLASSIC
STRAIGHT
LINEAR
STRAIGHT
LIFTMASTER
CURVED /
(SEARS)
STRAIGHT
CURVED /
GENIE
STRAIGHT
TYPICAL 1/2" - 1"
ABOVE HIGH ARC
TORQUEMASTER
COUNTERBALANCE
HIGH ARC
LINE
VERTICAL
CENTER LINE
FROM
STEP 12
HEADER
FIG. 3.2
CURVED
ARM
CUT STRAIGHT
ARM TO
ACCOMPLISH
TROLLEY
SETTING
FIG. 3.4
OPERATOR
BRACKET
HEX BOLT
TYPE OF ARM BEING USED
OPTIONAL
REF. ILLUSTRA-
HOOKUP
TIONS ABOVE
FIG. 3.4
STRAIGHT
FIG. 3.3
FIG. 3.3
N/A
N/A
FIG. 3.4
STRAIGHT
FIG. 3.3
FIG. 3.4
STRAIGHT
FIG. 3.3
®
35

Publicidad

Capítulos

Tabla de contenido
loading

Este manual también es adecuado para:

94009600

Tabla de contenido