Campbell Hausfeld WK250000AV Instrucciones De Funcionamiento Y Manual De Piezas página 5

Important Safety Information (Continued)
RISK TO EQUIPMENT: USING THE PLASMA CUTTER WITH A
PORTABLE GENERATOR
There are three common types of portable
◆
generators – brush, brushless, and inverter.
DO NOT operate this plasma cutter on a
brush type generator; voltage irregularities
may damage sensitive inverter electronics.
When powering the plasma cutter with a brushless generator,
◆
turn-off the idle-speed control. The response of an idle-speed
control is typically too slow and erratic startup of the plasma
cutter's arc will occur.
Use only a generator with a minimum of 4000 watts
◆
continuous output.
All generators will experience an engine RPM drop from
◆
suddenly applied loads. Hence, the plasma cutter will cause
a sudden drop in RPM when the torch arc is started. Engines
are typically equipped with governors that help the engine
return to normal speed under load. This usually happens
within a few seconds of when the engine senses the increased
load. To minimize the effect of this RPM drop on the plasma
cutter's arc, we recommend adding an additional 500 watt
load to the generator. This can easily be done with a halogen
light.
IMPORTANT: INTERFERENCE: H.F. RADIATION
High frequency (H.F.) radiation can
◆
interfere with radio navigation, safety
services, computers, and communications
equipment.
If notified by the FCC about interference,
◆
stop using the equipment at once and contact a qualified
electrician for assistance with the problem.
Keep covers properly installed and replace components and
◆
cables with original equipment components.
IMPORTANT: INTERFERENCE: ELECTROMAGNETIC
ENERGY
This unit can produce electromagnetic
◆
energy which can interfere with sensitive
electronic equipment such as computers
and televisions.
To reduce interference, keep cables close
◆
together and on the floor. Twisting or taping the cables
together or covering the cables with a cable cover will also
reduce interference.
Operate this unit at least 300 feet [100m] from sensitive
◆
electronic equipment.
Be sure the unit is connected to a grounded outlet.
◆
ADDITIONAL SAFETY STANDARDS
Refer to the following standards and / or regulations or their
latest revisions for more information:
Safety in Welding, Cutting, and Allied Processes
ANSI Standard Z49.1 from American Welding Society,
550 N.W. Le June Rd., Miami, FL 33126
Safe Practice for Occupational and Educational Eye and Face
Protection
ANSI Standard Z87.1 from American National Standards Institute
25 West 43rd Street, New York, NY 10036
Safety and Health Standards
OSHA 29 CFR 1910, from Superintendent of Documents,
U.S. Government Printing Office, Washington, D.C. 20402
NIOSH Approved Respirators
The National Institute for Occupational Safety and Health
(NIOSH) 395 E Street, S.W., Suite 9200, Patriots Plaza Building,
Washington, DC 20201
Recommended Practices for Plasma Arc Cutting and Gouging
AWS C5.2 from the American Welding Society,
550 N.W. Le June Rd., Miami, FL 33126
National Electrical Code
NFPA Standard 70, from National Fire Protection Association,
Batterymarch Park, Quincy, MA 02269
Safe Practices for the Preparation of Containers and Piping for
Welding and Cutting
AWS F4.1 from the American Welding Society,
550 N.W. Le June Rd., Miami, FL 33126
Safe Handling of Compressed Gases in Containers
CGA Pamphlet P-1, from Compressed Gas Association,
1235 Jefferson Davis Highway, Suite 501, Arlington, VA 22202
Code for Safety in Welding, Cutting, and Allied Processes
CSA Standard W117.2, from Canadian Standards Association,
Standards Sales, 178 Rexdale Boulevard, Rexdale, Ontario,
Canada M9W 1R3
Standard for Fire Prevention During Welding, Cutting, and
Other Hot Work
NFPA Standard 51B, from National Fire Protection Association,
Batterymarch Park, Quincy, MA 02269
OSHA, Safety and Health Standards, 29CFR 1910
Obtainable from the Superintendent of Documents
U.S. Government Printing Office, Washington, D.C. 20402
SAVE THESE INSTRUCTIONS
DO NOT DISCARD
WK250000AV
www.chpower.com 5