Important Safety Instructions; Safety Alert Symbol; Composite Heating Curing Blankets; Heater Characteristics / Specifications - BriskHeat Custom Serie Manual De Instrucciones

Ocultar thumbs Ver también para Custom Serie:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

IMPORTANT SAFETY INSTRUCTIONS

SAFETY ALERT SYMBOL

The symbol above is used to call your attention to instructions
concerning your personal safety. It points out important safety
precautions. It means "ATTENTION! Become Alert! Your
Personal Safety is involved!" Read the message that follows
and be alert to the possibility of personal injury or death.
DANGER
A person who has not read and understood all operating
Instructions is not qualified to operate this product.
DANGER

Do not immerse heater in liquid.

Keep volatile or combustible material away from
heater when in use.

Use heater only in approved locations

Keep sharp metal objects away from heater.

Never handle the heater while it is in operation.

Always disconnect the heater from power source and
allow to cool prior to removing from the surface.

Do not use in the presence of flammable or
combustible materials, fire or explosion may result.
The heater contains components which may ignite
such materials

Do not modify this product. Modification will void
warranty.
Failure to observe these warnings may result in electric shock,
risk of fire, and personal injury.
WARNING
End User Must Comply to the Following:

Only qualified personnel are allowed to connect the
electrical wiring.

Disconnect all supply power at the source before
making any heating cable power input connections.

All electrical wiring must follow local electrical codes.

The person who performs the final installation / wiring
must be qualified for this work.

The end-user is responsible for providing a suitable
disconnecting device.

The end-user is responsible for providing suitable
electrical protection device. It is highly recommended
that a ground fault circuit breaker be used.
Failure to observe these warnings may result in personal injury
or damage to the product and/or property.
®
© BriskHeat
Corporation. All rights reserved
SRL5, SR, SRV, FGH, and SXH
Composite Curing Blankets
DANGER
Immediate hazards which WILL result in severe personal injury or
death.
WARNING
Hazards or unsafe practices that COULD result in severe personal
injury or death.
CAUTION
Hazards or unsafe practices that COULD result in minor personal
injury or property damage.
OPERATION
Your Heating Blanket is designed to provide a long and efficient
service life. Overheating , contamination and misuse will greatly
reduce the life of the heater, Your heater should only be used in
dry, non-hazardous areas. Only use the heater on the surface it
is designed to heat.
CAUTION

Never operate heater without a temperature control
device. Failure to use such a device may result in
process damage or heater failure.

Inspect heater before use (see page 9)

Never operate a heater without an appropriate heat
sink (device being heated is considered to be a heat
sink).

Never expose the heater to temperatures above the
rated exposure temperature.

Fluid should not be allowed to come in contact with the
heater.

Never lift or pull the heater by its power cord or lead
wire.

Never cut, punch holes in or otherwise modify heater.

Do not use tools such as pliers or vice grips to pull or
tighten the heater.
Failure to observe these warnings may result in personal injury
or damage to the heater.
.
3

HEATER CHARACTERISTICS / SPECIFICATIONS

Part Series
SRL5
SR
2
Max Power Density
2.5 W/in
5 W/in
2
(W/in²)
(63.5 W/mm
)
(127 W/mm
Minimum Bend
3"
1/4"
Radius
(76mm)
(6 mm)
Max Exposure
450°F (232°C) 450°F (232°C)
Temperature
Max Humidity
95%
95%
Ingress Protection
IP56
IP56
Moisture and
Chemical Resistant
®
© BriskHeat
Corporation. All rights reserved
SRL5, SR, SRV, FGH, and SXH
Composite Curing Blankets
SXH
SRV
FGH
2
2
2
13 W/in
5 W/in
7 W/in
2
2
2
)
(127 W/mm
)
(177 W/mm
)
(330 W/mm
3'' (76 mm) With
Blanket Seal
1" (25.4mm)
1" (25.4 mm)
.25'' (6 mm)
Without
Blanket Seal
450°F (232°C)
450°F (232°C)
450°F (232°C)
95%
95%
95%
IP4X
IP56
IP4X
.
4
2
2
)

Publicidad

Tabla de contenido
loading

Productos relacionados para BriskHeat Custom Serie

Este manual también es adecuado para:

Srl5SrSrvFghSxh

Tabla de contenido