Customer Service; Replacing The Battery - Peg-Perego POLARIS SPORTSMAN 400 Empleo Y Manutencion

RULES FOR SAFE DRIVING
For the safety of the child, before starting up the
vehicle read and carefully follow the following
instructions.
• Teach the child how to use the vehicle properly for
safe and enjoyable driving.
• Before starting, check that there are no people or
objects obstructing the vehicle's path.
• Drive with hands on the handlebars/steering wheel
and always watch the road ahead.
• Brake in good time to avoid collisions.
2nd GEAR (if present)
Initially, use in 1st gear is recommended. Before
enabling 2nd gear, check that the child has learned to
use the handlebars/steering wheel, 1st gear and the
brake correctly, and has become familiar with the
vehicle.
WARNING!
• Check that all the wheel fixing studs/nuts are
fastened properly.
• If the vehicle is overloaded, as can happen on soft
sand, mud, or very uneven ground, the overload
switch will immediately disconnect the power. The
power supply will be restored after a few seconds..
• Only for 12 and 24 Volt vehicles: in first gear the
vehicle has a differential effect like a real motor
vehicle; on smooth terrain and with just one child
on board, the two wheels can turn at different
speeds and they can slip and slow down.
UNINTERRUPTED FUN: Keep a spare set of charged
batteries ready for use.
PROBLEMS?
THE VEHICLE DOES NOT WORK?
• Check that there are no disconnected cables under
the accelerator plate.
• Check the operation of the accelerator button and
replace it if necessary.
• Check that the battery is connected to the
electrical system.
THE VEHICLE LACKS POWER?
• Charge the batteries. If after charging the problem
persists, have the battery and charger checked by
an assistance centre.

CUSTOMER SERVICE

offers an after-sales assistance service,
PEG PEREGO
directly or through a network of authorized
assistance centres, for any repairs or replacements
and the sale of original spare parts. To contact the
assistance centres refer to the "Assistance Centres"
booklet included in the packaging.
The item's serial number must always be quoted.
See the page on spare parts to find out how to
identify the serial number.
Peg Perego always strive to best satisfy their
customers' needs. Knowing the opinions of our
customers is therefore very important and valuable
to us. We would be very grateful if, once you have
used the product, you would fill out the
which you can find on
SATISFACTION QUESTIONNAIRE
the internet at: www.pegperego.com, making
any observations or suggestions you might have.
ASSEMBLY INSTRUCTIONS
WARNING
ASSEMBLY MUST ONLY BE CARRIED OUT BY
ADULTS. TAKE CARE WHEN REMOVING THE
VEHICLE FROM ITS PACKAGING. ALL THE
SCREWS AND SMALL PARTS ARE CONTAINED IN
A BAG INSIDE THE PACKAGING. THE BATTERY
MAY ALREADY BE FITTED INSIDE THE ITEM.
1 • Check the forecarriage to be sure it is correctly
fastened at points (A). Remove the protective
caps (B).
2 • Insert an iron washer on the pin of the
forecarriage, as shown in the figure.
3 • (1)Insert one of the two front wheels: make sure
you use the wheel shown in Figure A. (2)Insert
an iron washer.
4 • Insert a self-locking washer on the provided tool
(shown in the figure). Caution: The tabs of the
self-locking washer must face the inside of the
tool (see small picture A). NOTE: the bag
contains 8 self-locking washers. Keep 4 of them
apart as spare washers.
5 • Fasten the wheel as shown in the figure, pushing
the self-locking washer down completely.
6 • Snap on the stud cover. Perform the same
operations as the ones in Figure 2 for the other
front wheel.
7 • Insert a self-locking washer on the provided tool
(shown in the figure). Caution: The tabs of the
self-locking washer must face the inside of the
tool (see small picture A).
8 • Remove the grey protective caps at the ends of
the rear axle. Insert the axle on the tool as
shown in the figure.
9 • (1)Insert an iron washer on the axle. (2)Insert
the axle into one of the two rear wheels: make
sure you use the wheel shown in Figure A.
10 • Insert the axle with the wheel into the hole of
the gearmotor, pressing to be sure it exits from
the opposite side of the vehicle.
11 • Turn the wheel slightly to match up the
gearmotor pentagon with the one on the wheel
(Figure shows incorrect fastening of the wheel).
12 • Insert the bushing as shown in the figure,
working from the other side of the shaft until it
is hooked to the body.
13 • Insert an iron washer as shown in the figure.
14 • Reposition the tool (used previously to insert
the self-locking washer - see Figure 7) on the
axle from the wheel side. Place the vehicle on
one side, keeping the wheel underneath. Make
sure the tool cannot shift.
15 • (1)Position the remaining wheel end insert an
iron washer. (2)Insert a self-locking washer on
the provided tool (shown in the figure). Caution:
The tabs of the self-locking washer must face the
inside of the tool (see small picture A). (3)Fasten
the wheel as shown in the figure, pushing the
self-locking washer down completely.
16 • Snap on the remaining stud covers on both sides.
17 • Slide on the handle, orienting it as shown in the
figure.
18 • Fasten the handle with a washer and screw.
19 • Push the handlebar cap on.
20 • Slide the grips onto the handlebar.
21 • Place the handles on the rear of the vehicle,
ensuring that they are facing the right way: the
lower end must be closer to the front of the
item, as shown in the figure.
22 • Attach the handles with the 4 screws provided.
23 • Rotate the red catch behind the saddle until
bringing it to the position shown on figure. A: the
saddle is locked. B: the saddle can be lifted. Lift
up the saddle.
24 • Connect the two plugs.
25 • Reposition the saddle by sliding the two pins into
the holes on the tank. Turn the red catch behind
the saddle in order to fasten it. The vehicle is
ready to use.
FEATURES AND INSTRUCTIONS FOR USE
26 • GEARSHIFT LEVER: Your child will have fun
pretending to change gears using this gearshift
lever, which can be rotated into two positions.
27 • ACCELERATOR/ELECTRIC BRAKE PEDAL: The
vehicle brakes automatically when your child lift
his/her foot off the pedal.

REPLACING THE BATTERY

CONSUMER
PLEASE NOTE: THE PICTURES OF THE BATTERIES
ARE FOR ILLUSTRATIVE PURPOSES ONLY. YOUR
BATTERY MAY BE DIFFERENT FROM THE MODEL
SHOWN. THIS DOES NOT AFFECT THE
ASSEMBLY
REPLACEMENT AND CHARGING PROCEDURES
DESCRIBED.
28 • Rotate the red catch behind the saddle until
bringing it to the position shown on figure 23
(figure B). Lift up the saddle. Unplug the
terminals. Unscrew the battery fastener. Remove
the battery fastener.
29 • Replace the battery. Replace and screw back on
the battery fastener. Connect the two plugs.
CAUTION: When you have finished, remember
to close and fix down the seat.
BATTERY RECHARGE
WARNING: BATTERY CHARGING AND EVERY
OTHER OPERATION ON THE ELECTRICAL
SYSTEM MUST BE CARRIED OUT BY ADULTS
ONLY.
THE BATTERY CAN ALSO BE CHARGED
WITHOUT REMOVING IT FROM THE TOY.
30 • Unplug vehicle wiring terminal A from battery
terminal B, by pressing terminals on side and
pulling apart.
31 • Plug the battery charger terminal to a wall
outlet following the instructions enclosed.
Connect the plug B to the battery charger plug
C.
32 • Once the charge is completed unplug recharger
from wall outlet. Unplug recharger cord terminal
C from battery terminal B.
33 • Plug battery terminal A into vehicle wiring
terminal B. Close saddle.