Stop Of The Machine After Cleaning Operation; Daily Maintenance; Recovery Tank Cleaning; Suction Filter Cleaning - Tornado 99680T Manual De Instrucciones

STOP OF THE MACHINE
CLEANING OPERATION
Before executing any type of maintenance:
1. Close the solution valve lever (8) and check that
the indicator of open solution valve (4) on the in-
strument board turns off.
2. Lift the brushes base acting upon the pedal (10).
3. Lift the squeegee acting upon the lever (9).
4. Turn the brushes motor switch off (5).
5. Turn the suction motor switch off (3).
6. For machines equipped with key switch (see un-
der "OPTIONAL ACCESSORIES"), turn the key (6)
counterclockwise.
7. Bring the machine to an appropriate place for
tanks draining.
ATTENTION:
The machine is not equipped with a parking brake,
therefore do not leave it on slopes.

DAILY MAINTENANCE

RECOVERY TANK CLEANING

1. Hold the exhaust hose placed in the front part of
the machine.
2. Take off the exhaust plug acting upon its lever
and empty the recovery tank into appropriate con-
tainers (see under "OVERFLOW DEVICE").
3. Take off the suction cover (1) after rotating the
blocking levers (2).
4. Take off the filter and filter protection.
5. Rinse the tank with a water jet.
ATTENTION:
This operation must be carried out using gloves to
protect from contact with dangerous solutions.

SUCTION FILTER CLEANING

1. Take off suction cover (1) after rotating the
blocking levers (2).
2. Take off the filter and filter protection.
3. Clean all parts with a water jet especially inside
surfaces and filter bottom.
4. Carry out carefully the cleaning operations.
5. Reassemble all parts.
AFTER

BRUSH/ES CLEANING

Disassemble the brushes and clean them with a wa-
ter jet (for the disassembly see as follows under
"BRUSHES DISASSEMBLY").

BRUSHES DISASSEMBLY (ruby 45t, ruby 55t)

1. Lift the brushes base lowering the pedal (10).
2. Switch off the machine acting upon the general
switch (12). For machines equipped with key switch
(see under "OPTIONAL ACCESSORIES"), turn the key
counterclockwise.
3. With the brushes base in lifted position, turn the
brush in its rotating sense, until it is released from
the brush holder plate seat as indicated in the figure.
The following figure shows the rotating sense for
brushes release on the models ruby45t and ruby55t.
ATTENTION:
The execution of brushes disassembly operations
with electric supply on, may cause damages to hands.
AUTOMATIC BRUSH DISASSEMBLY (ruby 50t, ru-
by 50bh)
1. Lift the brush base lowering the pedal (10).
2. Act upon the levers drive control (7) and simul-
taneously press the push button (11) of the brush re-
lease. In this way the brush is uncoupled automati-
cally.
3. Release the push button and the levers.
4. Switch off the machine acting upon the general
switch (12). For machines equipped with key switch
(see under "OPTIONAL ACCESSORIES"), turn the key
counterclockwise.
The handling of the brushes operation must be car-
ried out using suitable gloves to protect both me-
chanically from contact with the bristles and the
chemical risk of contact with dangerous solutions.

SQUEEGEE CLEANING

Keeping the squeegee clean guarantees always the
best drying action.
For the cleaning it is necessary to:
1. Take off the squeegee hose (3) from its coupling.
2. Disassemble the squeegee from its support by ro-
tating the lever (2) counterclockwise and making
slide the stud bolts (1) in their slots up to their re-
lease.
3. Clean with care the internal part of the squeegee
inlet eliminating eventual dirt residuals.
4. Clean with care the squeegee rubbers.
5. Reassemble all parts.

WEEKLY MAINTENANCE

REAR SQUEEGEE RUBBER REPLACEMENT

Check the squeegee rubber wear and eventually turn
or replace it.
For the replacement it is necessary to:
1. Lift the squeegee acting upon the lever (fig. 1,
pos. 16).
2. Uncouple the hook (1) of the rubber holder blade,
release the extremities (2) from the squeegee body
and take off the rubber (4).
3. Turn the rubber (4) to a new side or replace it.
To reassemble the squeegee repeat reverse the op-
erations above-mentioned, inserting the rubber (4)
on the guides (3), couple the extremities (2) of the
rubber holder blade onto the squeegee body and fi-
nally block the hook (1).
23
ATTENTION: