Introduction; Machine Specifications - American Sanders EZ-8 Manual Del Usuario

EN
Control Switch
Control Link
Locking Collar
Handle Latch
Level Adjustment
Model
Abrasive Size
Abrasive Rate
Drum Rate
Dust Control Rate
Drum Pressure
Leveling Controls
Operating Controls
Motor
Power Cable
40΄ (12.1m) 12 Gauge
Voltage Frequency
Amperage
Dimensions (in)*
(54.6 x 40.6 x 90.2 cm)
Weight (lbs) *
* Shipping Value
Use only an approved extension cord with three conductors, a plug with three terminals, and a connector body with three holes.
WARNING: If you use an extension cord, use an extension cord with minimum wire size 12 AWG. Do not use an extension cord longer than
50 feet. Do not join two extension cords.
Use only an approved extension cord with two main conductors and one earthing conductor.
WARNING: If you use an extension cord, use an extension cord with minimum wire size 1.50 mm2. Do not use an extension cord longer
than 15 meters. Do not join two extension cords.
WARNING: Do not cut, remove, or break the ground terminal. Do not try to fit a three-terminal plug into a receptacle or connector body that
does not fit the plug. If the receptacle or connector body does not fit the plug, see your Authorized person to make the
connection.
Operating
Control Lever
Dust Pipe
Transport Handle
Drum Cover
07012A
8˝ x 19˝sleeve 8˝ x 19˝sleeve
(20.3 x 48.2 cm) (20.3 x 48.2 cm)
2830 ft/min
1800 RPM
76 CFM
25 lbs (11.4 kg) 25 lbs (11.4 kg)
Externally Adjustable Externally Adjustable
Lever Operated Lever Operated
1½ HPTEFC 1½ HPTEFC
Thermally Protected Thermally Protected
40΄ (12.1m) 12 Gauge
Abrasive Resistant Abrasive Resistant
115 / 60
12
21½˝ x 16˝ x 35½˝ 21½˝ x 16˝ x 35½˝
(54.6 x 40.6 x 90.2 cm)
125 (57 kg)
Extension Cords (120V)
Extension Cords (230V)

Introduction

CAUTION:
07058A 07060A
8˝ x 19˝ sleeve
(20.3 x 48.2 cm)
2830 ft/min 2830 ft/min
1800 RPM 1500 RPM
76 CFM
64 CFM
25 lbs (11.4 kg)
Externally Adjustable
Lever Operated
1½ HPTEFC
Thermally Protected
50΄ (15.2m)12 Gauge
Abrasive Resistant
115 / 60 240 / 50
12 6
21½˝ x 16˝ x 35½˝
(54.6 x 40.6 x 90.2 cm)
125 (57 kg) 125 (57 kg)
6
Your equipment may be inappropriate on some
installations. Always consult with the flooring
manufacturer on the proper installation, preparation,
and finishing of their product. Determine suitability of
your equipment in preparing the product.
07084A
8˝ x 19˝ sleeve
(20.3 x 48.2 cm)
2830 ft/min
1500 RPM
64 CFM
25 lbs (11.4 kg)
Externally Adjustable
Lever Operated
1½ HPTEFC
Thermally Protected
40΄ (12.1m) 12 Gauge
Abrasive Resistant
240 / 50
6
21½˝ x 16˝ x 35½˝
(54.6 x 40.6 x 90.2 cm)
125 (57 kg)
07057A
8˝ x 19˝ sleeve
(20.3 x 48.2 cm)
2830 ft/min
1800 RPM
76 CFM
25 lbs (11.4 kg)
Externally Adjustable
Lever Operated
1½ HPTEFC
Thermally Protected
40΄ (12.1m) 12 Gauge
Abrasive Resistant
115 / 60
12
21½˝ x 16˝ x 35½˝
(54.6 x 40.6 x 90.2 cm)
125 (57 kg)