Assembling The Seat - Jacuzzi Mynima Serie Manual De Instalación

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

lines up with glass panel "D". If not, turn component "S2" until
it rests on the glass panel (
i
I (
20 detail 2B) At this point, fasten the glass panel as shown,
then put on cap "S6".
Installing compensator "E"
i
I (
21 detail 1) Drill holes in compensator "E", using the holes
already present as a guide.
i
I (
21 details 2-3) Always checking the position of glass pan-
el "D", using the template provided, move compensator "E" so that it
lines up with the profile as shown.Mark the points for drilling holes.
i
I (
21 detail 4) Remove the compensator, drill and insert the
plugs. Apply silicone to the rear part of the compensator as shown
(detail 5), then put the compensator back in place and attach it
as shown (detail 6).
i
I (
22 detail 1) Using the holes in compensator "E" as a guide,
after checking for level, drill holes in the profile of glass panel
"D". Then fasten the compensator as shown.
N.B. The maximum projection allowed for the glass panel in re-
lation to the compensator is 10 mm.
i
I (
23 detail 1) Using the appropriate tool, insert seal "L" be-
tween glass panel "D" and glass panel profile "B", making sure
it is in the correct position. (detail 2) Then apply silicone to the
base of the glass panel profile, as shown.
N.B. To prevent the silicone from being visible, remove glass
panels "D" and "B" and apply silicone to the shower tray, and
to the area the profiles are resting on.
VARIATION FOR MODELS WITHOUT WALL-MOUNTED
GLASS PANELS
i
I (
21A detail 1) Position compensator "E" in the installation
corner, according to the given measurements.
Check that it is level and mark the holes for drilling holes as shown.
WARNING! Measurements refer to the edge of the shower tray,
not the wall.
i
I (
21A detail 2) Remove the compensator, drill the holes and
insert the dowels. Apply silicone to the rear part of the compen-
sator as shown (detail 3). Then replace the compensator and, af-
ter checking that it is level, fasten it as shown (detail 4).
Installing glass panel "F"
i
I (
24 detail 1) Fasten the foam rubber protective strip to the
part of the glass panel that faces the wall.
i
I (
24 detail 2) Starting with the aluminium profile, attach the
bottom seal (check that the glass part that fits into the fixture
panel is not covered by the seal).
Then insert glass panel "F" into the fixture panel as shown and
slide it until the required distance is obtained, checking that it is
perpendicular with the fixture panel (details 3-4).
Installing compensator "G"
i
I (
25 detail 1) Drill holes in compensator "G", using the holes
shown as a guide.
i
20 detail 2A).
i
I (
25 detail 2-3) Line compensator "G" up with the profile
as shown and mark the holes for drilling.
i
I (
25 detail 4) Remove the compensator, drill and insert the
plugs. Apply silicone to the rear part of the compensator as shown
(detail 5) then put the compensator back in place and attach it
as shown (detail 6).
i
I (
26 detail 1) Check that the glass panel and the column
are perpendicular. Then, using as a reference the holes compen-
sator "G", after checking for level, drill the profile of glass panel
"F"; then attach the compensator with the screws indicated.
The maximum projection allowed for the glass panel in relation
to the compensator is 10 mm.
i
I (
26 detail 2) Using the appropriate tool, insert seal "L2" be-
tween the glass panel and the fixture panel, making sure it is in
the correct position.
VARIATION FOR MODELS WITHOUT WALL-MOUNTED
GLASS PANELS
i
I (
25A detail 1-2) Position compensator "G" in the installa-
tion corner, according to the given measurements.
Check that it is level and mark the holes for drilling holes as shown.
WARNING! Measurements refer to the fixture panel wall.
i
I (
25A detail 3) Remove the compensator, drill the holes and
insert the dowels. Apply silicone to the rear part of the compen-
sator as shown (detail 4). Then replace the compensator and, af-
ter checking that it is level, fasten it as shown (detail 5).

Assembling the seat

for TT models
i
I (
27 detail 1) Position the seal in its place and move the
seat towards the fixture panel. Then connect the overflow pipe to
the connector situated under the seat (detail 2).
i
I (
28 detail 1) Fasten the seat to the fixture panel.
i
I (
28 detail 2) Then connect the pipes (marked) as shown,
by fastening them to the seat.
N.B.: The pipe on the right (A) is for air, while the one on the
left (B) is for steam.
i
I (
28 detail 3) Complete this operation by fastening the seat.
for TB models
i
I (
28A detail 1) Position the seal in its place and fasten the
seat to the fixture panel (detail 2).
i
I (
28A detail 3) Fasten the seat.
INSTALLING THE EXTERNAL GLASS PANELS
Installing glass panel "H"
i
I (
29 detail 1-2) Attach the spacers to the crossbar.
i
I (
30-30A detail 1) Starting with the aluminium profile, at-
tach the bottom seal.
13

Publicidad

Tabla de contenido
loading

Tabla de contenido