CIAT CS2B Manual De Instalación página 12

5. Press the mode (M) button to save settings
and enable the next parameter to be
changed. The parameter number will be
¹ËÀÁÆ¿
6. Press up and down button to go to the next
parameter. (If the current display is at
parameter number).
7. You can program all your parameters by
following the same procedure. Once you
completed, press OK or zone (
to save your settings and will return to the
normal display screen.
8. Close the lid.
NOTE: Refer to parameters table in the main unit
documentation for more details.
Ë½Ê »ÇÆ ¿ÍʹÌÁÇÆ ¼½¾¹ÍÄÌ Ê½Ë½Ì
Procedure for Changing the User Parameter settings to
Default values is given below.
1.
Press simultaneously home (
Away ( ) buttons at a time for 10
seconds to enter into the user
»ÇÆ ¿ÍʹÌÁÇÆ ÅǼ½ À½Æ ÌÀÁË Ë½ÌÌÁÆ¿ ÁË
ÊËÌ Ë½Ä½»Ì½¼ ÏÁÄÄ º½ ¼ÁËÈĹѽ¼ ÁÆ ÌÀ½
time display area and an initial value of 10
will be displayed in the temperature display
area.
2. Press and hold the down button. When the
counter reaches zero, "Fd" will be
displayed in the temperature display area.
This represents factory defaults are in
progress. Upon successful completion of
restoring defaults to EEPROM, the NUI will
then force a reset.
12
) button
) and
    
ÇÇÅ ½ÅȽʹÌÍʽ ½ÆËÇÊ ¼ÂÍËÌŽÆÌ
NUI offers a feature where you can add or subtract an
offset to the displayed room temperature. This allows the
NUI to display the correct temperature of the room even
if the NUI or the room temperature sensor is installed at a
location where there is a slight difference in temperature.
In this case, the TROOM SENSOR ADJ variable can be
MODIlED IN A RANGE OF ›#  ›# AND THIS VALUE WILL BE
mathematically added to the real Room sensor value.
Refer to the parameters table in the main unit
documentation.
ÀÇÊÌ ÍÌ ÌÇ ÁĽÆÌ Ǽ½
Press the Hold ( ) key for 10 seconds to make Silent mode
active. Deactivate Silent mode by pressing the Hold ( )
key again for 10 seconds.
When Silent mode is active, NUI will display the (
If Silent mode is active, this will always override the
selection done in program schedule.
½ÑºÇ¹Ê¼ Ç»Ã
To Lock all key and block command functions
1. Open the lid.
2. Press and hold for 3 seconds the three
buttons days ( ), period (
time.
3. All the keys will be disabled and the lock
icon ( ) will be visible on display.
4. To unlock the keyboard press again the
three buttons for 3 seconds.
The lock icon ( ) will disappear.
ÄÇ»Ã
The clock will continue to operate for 8 hours while power
is removed.
 
¹ÍÄÌ Ç¼½ ¹ºÄ½
In case of system failure, the alarm icon ( ) will light up.
&AILURES ARE IDENTIlED BY A FAULT CODE !CTIVE FAULT CODES
WILL BE DISPLAYED IN SEQUENCE WITH A CHANGE RATE OF 
second.
Refer to the main unit documentation for a description of
the fault codes.
) and start
) icon.