CIAT CS2B Manual De Instalación página 9

½Ä½»ÌÁÆ¿ ÌÀ½ ÒÇƽ
To show temperature, humidity, Touch'N'Go settings and
SETPOINT OF A DElNED ZONE
1. Open the lid
2. Press the zone button ( ) to select the desired
ZONE :ONES ARE INDICATED AS FOLLOW
0. NUI zone
1. Heating / cooling zone 1
2. Heating / cooling zone 2
3. Domestic water
Ç »À¹Æ¿½ ÌÀ½ ¾¹»ÌÇÊÑ Ë½ÌÌÁÆ¿Ë
1. Press and hold the comfort button
or or
( ) to be changed for
¹ºÇÍÌ Î½ ˽»ÇÆ¼Ë À½ Ë½Ì Ì½ÅȽʹÌÍʽ
along with the symbol heat (
( ÏÁÄÄ ¹ËÀ
2. Select the desired zone by pressing the
zone ( ) button repeatedly.
3. If zone 1 or 2 is selected, press the mode
(M) button to switch between heat (
and cool ( ).
4. Press the up or down button on the right
side of the display until you reach the
desired temperature setting for the current
mode of operation. At this moment the
triangle icon ( ) above the pressed
comfort button (
¹ËÀÁÆ¿
5. Press the up or down button on the right
side of the display until you reach the
desired temperature setting
6. Pressing one of the other two Touch 'N' Go
button, item 4 to 5 can be repeated
7. ¾ ƽ½¼½¼ ˽Ľ»Ì ¹ ¼Á ½Ê½ÆÌ ÒÇƽ ¹Æ¼
repeat steps 3 to 6.
8. ʽËË  ºÍÌÌÇÆ ÌÇ »ÇÆ ÊÅ »À¹Æ¿½Ë ¹Æ¼
exit from the Comfort change mode
) or cool
)
) will start
À¹Æ¿ÁÆ¿ ÌÀ½ ̽ÅȽʹÌÍʽ ÌÁŽ ȽÊÁǼË
After you have set temperature settings for home, away
and sleep, you can program the time of day you want to
use for those temperature settings.
Time ranges are called periods; zone 1 and zone 2 have
maximum 6 periods; zone 3 has maximum 4 periods.
0ERIODS ARE IDENTIlED ON THE DISPLAY AS 0 0 0 0 0
and P6.
The thermostat has preset periods (see below), but you can
CHANGE THESE TO lT YOUR LIFESTYLE
To select the number of periods, refer to the (user)
parameters table in the unit documentation.
½ÊÁǼ ̹ÊÌ ÁŽ
½ÊÁǼ
Zone 1 / Zone 2
P1 6:00
P2 8:00
P3 12:00
P4 14:00
P5 18:00
P6 22:00
NOTE: Zone 1 and zone 2 have the same time periods.
ËËÁ¿ÆÁÆ¿ ÌÁŽ ȽÊÁǼË
It is possible to assign the following parameters to each
time period.
:ONE  2OOM TEMPERATURE
(ON/OFF), Silent mode (ON/OFF)
:ONE  2OOM TEMPERATURE
(ON/OFF)
:ONE  $OMESTIC HOT WATER TEMPERATURE
( ), booster heater (ON/OFF)
/
Here is an example of a programming using the factory-set
periods and Touch 'N' Go options.
Zone 3
6:00
8:00
18:00
24:00
Not available
Not available
/ / ), Zone mode
), Zone mode
/ /
9