Rubi DU EVO Instrucciones Originales página 4

4.
INDEX
A. ASSEMBLY INSTRUCTIONS
• Assembly
• Safety
• Hooking up
• Applications
• Recomendations concerning the work area
B. STARTING THE MACHINE
• Items to be checked before starting the machine
C. INSTRUCTIONS FOR USE
D. MAINTENANCE
A.ASSEMBLY INSTRUCTIONS
Assembly
Once you have unpacked your machine, check to make sure that there are no damaged or broken
parts. If there are, and you need to change these components they must only be replaced by original
of the manufacturer (if in doubt, consult the manufacturer).
Safety
Read carefully and understand the safety measures before the use of the machine.
Hooking up
Check that the voltage and frequency of the machine shown on the characteristics plate match the
electric system. (fig. 1)
Coil feeding cable during transport. Never move the machine by tugging at the cable.
Applications
Use: Models DU-EVO are basic machines for the straight or mitred cutting of building materials, and
work by means of a guided bearing system. Such cuts are made with water-cooled diamond blades.
Recommendations concerning the work area
Pay close attention to the state of the area where the job is to be done. Keep it clean and well lit.
The machine should be kept clean at all times in order to ensure optimum performance and the
safest working conditions.
B. STARTING THE MACHINE
Items to be checked before starting the machine
1. Before using this machine, verify that no parts are worn out, damaged or broken. Should
you find any part that is not in proper condition, have it repaired or replaced immediately.
2. Levelling the machine: (fig. 2, 3).
3. Check that the stops of the machine are perpendicular to the blade. These are regulated
before leaving the factory. (fig. 4)
4. Ensure that the voltage and frequency of the machine shown on the characteristics plate
match the electric system. (fig. 1)
5. The electrical outlet must have an earth connection and protection in the event of leaking
(differential). When using an extension, check that the cable section is at least 2.5 mm².
6. The disc cover protection, protects to the user of possible cuts during the work.
7. Install head's handle in the hole with M10 thread. (fig. 5)
8. Install wheels by using 10 mm wrench and 5 mm Hex Key (both provided with the machine).
(fig. 6, 7) and following these steps:
A.- To fix the support to the chassis with M6 nuts. 10 mm wrench.
B.- Install wheel, screw and nut. 5 mm Hex Key + 10-13-19 wrench.
9. Deploy the legs of the machine, making sure that are perfectly open.
10. Place the water tank in the defined area. (fig. 8)
11. Put the water pump into the tank.
12. Machine's head has a breaking system to avoid any movement during transport. To start
cutting, release the break. (fig. 9)
C. INSTRUCTIONS FOR USE
1. To install or replace the blade, first remove the protective cover to reveal the drive. shaft.
Insert the blade between the blade discs, turning in the direction shown on the machine.
Tighten the screw as illustrated 10, 11.
2. Fill the base with water until the water pump is completely covered. Working with clean water
gives your blade longer working life and improved performance. (fig. 12)
3. Models DU-EVO are equipped with a table-stand for placing the ceramic tile, and.a sliding
motor unit. This system enables you to handle all types of ceramic tile with maximum
precision and comfort. (fig. 13)
4. Movement takes place by means of wheels equipped with greased, sealed ball bearings.
5. To prevent accidents, shut the motor off when changing from the straight cutting position
to that of mitred cutting (and viceversa), changing cutting height and adjusting stops for
repeated cuts.
6. The starting of the machine will be made by pressing the tilted switch, and the same to
disconnect. (fig. 14)
7. DU-EVO have a safety system that protects the motor from overheating.
8. If the motor should stop for no apparent reason, wait a few minutes as it has probably been
overworked. Moderate the speed in subsequent cutting.
9. Once the machine is operating, wait until the motor and the water supply by the pump
return to normal (4 or 5 seconds).
10. To make correct cuts, guide the blade firmly and evenly, without brusque. One incorrect
move can break the workpiece and seriously damage the blade.
11. For 45º cuts (mitred cuts), there is a system of mechanical blockage, which enables you to
position the head with great precision. (fig. 15, 16)
English
TRANSLATION OF THE ORIGINAL
E. SAFETY INSTRUCTIONS
• Symbols
• Precautions
• Workspace
F. GENERAL CHARACTERISTICS
• Technical characteristics
• The overall machine
• Accessories
• Declaration of compliance with EEC regulations
• Electric mitring saws for tiles
12. When the chassis is fixed in place, the moveable stop will be adapted to turn between
-45º, 0º and 45º. This enables you to firmly position the workpieces to be cut, and to make
repeated cuts. (fig. 17, 18)
13. For the proper functioning of models DU-EVO work on level floor surfaces.
14. Never use diamond blades that are cracked or chipped.
15. Never use lateral pressure to stop the blades.
16. Read these instructions carefully before using this product. Keep them in a safe place for
future reference.
17. Keep cutting tools clean and sharp for better, safer performance:
18. Remove wrenches and tools before switching on the machine.
19. Make sure that the switch is in the "off" position when plugging in the machine.
20. When using the machine outdoors, use only extensible cord designed for this purpose.
21. Before using a machine again, check carefully to ensure that it is in proper working. order for
the task you have in mind for it. Any damaged element, whether protective or not, should be
repaired or replaced by an authorised technical service outlet, unless otherwise specified in
this instruction manual. Do not use the machine if it cannot be switched on and off.
22. It is essential to have adequate artificial lighting in work areas when the ambient light is
insufficient.
23. The machine put out off service must be carried out according to the instructions of each
country at a collection point, for proper classification and treatment of materials.
D. MAINTENANCE
Cleaning and maintenance
1. Before cleaning, maintenance or repair of the machine, or transport, the machine must be
turned off and unplugged.
2. Do not use aggressive cleaning products for cleaning the machine.
3. The machine must not be immersed in water.
4. Examine periodically the machine cables, if they are damaged must repair them through an
authorized technical service.
5. You must maintain the grips dry, clean and free of fat and oil.
6. To keep your machine in good condition, we recommend that you clean it with water after
using it and run clean water through the cooling system,especially to clean the submer sible
pump.
If in any doubt about the setting or operation of the machine please contact our after-sales service
for assistance.
Storage
Store the machine in a cool, dry, place, protected from direct sunlight.
The decommissioning and dismantling of the machine must be carried out according to the
instructions of each country at a collection point for the correct classification and processing of
materials.
After-sales service
Use only accessories and original spare parts supplied by the manufacturer. Repairs should only be
carried out by an accredited workshop or RUBI technical support:
GERMANS BOADA SANTA OLIVA
Ronda de l'Albornar, 24-26
43710 Santa Oliva
Tarragona (Spain)
Tel: +34 977 16 90 50
E. SAFETY INSTRUCTIONS
Symbols
• Carefully follow instructions when changing accessories.
• Periodically check the cables of this machine. Should they show signs of damage or
wear and tear, have them repaired at an authorised technical service outlet.
• Keep holders clean, dry and free of grease and oil..
Read the instruction manual
Caution
Rotation of the disc
Prohibited use-segmented