Novik Neo NVK 16M USB Manual De Instrucciones página 5

FUNCTIONS AND CONTROLS
28. Phantom Power (+48V)
This button turns on the phantom power in the XLR connectors of the microphone´s
input channels. This let you use condenser microphones or active direct boxes.
Make sure you are not using unbalanced lines in the XLR inputs when the Phantom
Power is active because it can cause serious damage in the unit. Make sure you set
all the output levels in minimum before activating or deactivating this function. Do not
activate the phantom power before connecting the microphone.
29. Vumeter
30. Effects Return Control
It establishes the return signal level of effects. If you use an external unit of effects,
through this control you can determine the signal level that enters into the mix.
31. MIX/ SUB Routing Button of effects return.
This button allows you to choose where the stereo return signal is routed. When being
pressed, the signal is routed to the SUB bus and if it is not pressed, the signal is routed
to the main output MIX BUS (L+R).
32. FX General Control/ FX Output
It establishes the post-fader sending level sent to the internal effects processor unit and
to the FX output.
33. Main Graphic Equalizer
The main output equalization can be controlled with a ±12dB gain centered in 7 bands of
frequencies: 63Hz, 200Hz, 500Hz, 1kHz, 4kHz, 6.3kHz and 16kHz. This will allow you to
modify general aspects of the mix tone and avoid feedbacks.
34. Earphones output level control
35. MIX/SUB of PFL Routing Button
When no PFL button is pressed, pressing this button will allow you to monitor the main
mix or the sub mix SUB through the earphones.
36. SUB TO MIX Routing Button
When pressing this button, the signal of the SUB mix will be routed to the main stereo
MIX.
37. CD/TAPE TO MIX Routing Button
When pressing this button, the signal of the CD/TAPE is routed to the main stereo MIX.
38. CD/TAPE TO SUB Routing Button
When pressing this button, the CD/TAPE signal is routed to the SUB mix.
39. FX Fader
It adjusts the signal level of the internal effects that is sent to the main MIX or to the
subgroup SUB according to where it is routed to the signal.
40. SUB subgroup Fader
This fader controls the output general level of the subgroup SUB.
41. Main Mix Faders
These two faders (Left - Right) control the output general level of the console.
42. CD/ TAPE Fader
It controls the CD/TAPE signal level sent to the MIX or SUB bus according to where it is
routed to.
43. SUB Subgroup Output
Line output of the SUB subgroup mix of the console.
44. Aux 1 Output
Line output used to send a signal to an amplifi er system for monitoring. Thisis a Pre-
fadersending.
FUNCTIONS AND CONTROLS
45. Aux 2 Output
Line output used to send the signal to an amplifi er system for monitoring. This is a Pre-
fader sending.
46. Stereo Return
Line inputs to connect the effect return of an external effects processor.
47. Main Mix Output
The stereo output is provided with balanced XLR and TRS of 1/4" TRS connectors that
are used to send the audio signal to the amplifi er.
48. Control Room Output
1/4" TS input used to send the signal to the monitor speakers or to a second PA set.
49. CD/TAPE Input/Output
RCA input and output. The input allows you to connect a stereo signal to the console.
The output allows you to record in an external device the main mix.
50. FX Output
Line output used to connect an external effects processor or to an additional monitoring
system. Thisis a post- fader sending.
51. Earphones Output
52. Console On Led
53. PHANTOM POWER +48V On Led
54. On/Off
55. Fuse
56. Power Supply
AC LINE INPUT
90 – 240V~60/50Hz 45W
MAIN FUSE
56
POWER
F: T1.6 AL 250V
54 55