Testing Menu; Others; Things To Do Before Calling The Service; Acoustic Signals - TEM TAB D-O Serie Manual Del Usaurio

tare always are
transmitted.
For printer type
models see related
documents.
10.6 Only sending Weight data (0ff)
If it is ON send simply Weight data.

11. Testing Menu:

Not in this type.

12. Others:

12.1 Approved
(On)
(It can be changed, if
the calibration key is
ON.) If it is turned
ON, all settings
depended on
condition
"APPROVED"
returns to factory
settings values.
12.2 Starting delay (10sn)
(On)
(If it is approved, it
cannot be changed)
12.3 Calibration Switch
(Off)
If calibration switch
is off, settings with
related calibration
swichs can not
change. Password is
required to change
position of calibration
switch.
calibration switch
position is changed
to ON from OFF by
this operation,
event counter
increased by
one.The
verification
weighing
insturment
broken.(Please
look COMMENTS
ON
VERIFICATİON.)
THINGS TO DO BEFORE CALLING THE
SERVICE
FAILURE SIGNALS
: Turn off the scale and
ER 1
then turn on it again. If
failure continues,
service.
: Wait for a while. Turn
ER 2
off the scale and then
turn on it again. If failure
still continues,
service.
: Wait for a while. Sure
ER 3
weighing plate is empty
and press
O
failure continues, turn off
the scale and then turn
on it again. If failure still
continues, call service.
: Turn off the scale and
ER 4
then turn on it again. If
failure continues,
service.
: Initial zero setting range
ER 5
control error. Weighing
not allowed.
Be sure the weighing
plate is empty. (If the
weighing plate is not on
scale, put it on to the
scale)Turn off the scale
If
and turn it on again,
when the weighing plate
is empty.
Call the service if this
warning is active again,
when the weighing plate
is empty.
of
- 19 -
ER 6
is
ER 7
ER 8
call
call
ER 9
key. If
ER 11
call
ER 12
ER 13
: Turn off the scale and
ER 14
turn on it again. If failure
continues, call service.
: Turn off the scale and
then turn on it again. If
failure continues, call
service.
: Interface
communication error.
Turn off the scale and
ER 15
then turn on it again. If
scale is not pc/printer
type and error still
continues, call the
service.
ER 16
If scale is pc/printer type,
change SET 10.1 to
"On" and turn off the
scale and turn on it
again. If still continues
Lo bAtt
call the service.
: Turn off the scale and
then turn on it again. If
failure continues, call
service.
Full
: Turn off the scale and
then turn on it again. If
nnnnnn
failure continues, call
service.
: Turn off the scale and
then turn on it again. If
failure continues, call
service.
: For pc/printer type
models, If alibi memory
is full, this message will
be shown. There will be
no data transmission to
the PC/Printer and new
transaction will be
blocked until alibi
memory erased.
Erase alibi memory, turn
off the scale and then
turn on it again. For
Printer type models see
related documents.
- 20 -
: Loadcell cable
detection error. Check
loadcell connector and
cable. If the connector is
unplugged, plug it again.
If failure continues, turn
off the scale and then
turn on it again. If failure
still continues, call
service.
: Wait for a while. If
failure continues, turn off
the scale and then turn
on it again. If failure still
continues, call service.
: See
"PrinterUserManualAnne
x.doc". If failure
continues, call service.
: The battery is empty.
Scale does not work. It
should be charged or
changed as soon as
possible.
: Weight is more than
maximum capacity.
: Platform (load carrier)
is not fitted, or when
there is weight on the
platform weighing
instrument may be tried
to open up. On the
empty platform. (The
platform is not installed,
replace) If necessary,
there was no load on the
instrument a more open
platform.
If load carrier has two
platform, you make sure
to empty on load carrier.
The platform was empty,
If failure still continues,
call service.

ACOUSTIC SIGNALS