Safety Regulations; Main Parts - Atlas Copco COBRA 148 Instrucciones Para El Operario

English
These instructions contain important sections dealing with safety.
Special attention must be paid to all framed safety text that begins with a warning symbol (triangle) followed by
a signal word, as shown below.
WARNING
CAUTION
G
Before starting the machine, read through
these instructions carefully.
G
Also read through the red safety instruc-
tions before putting the machine to use.
G
For reasons of product safety, the machine
must not be modified.
Data
Cobra 148.....................................Combined rock drill and
Cobra 149.....................................Combined rock drill and
Cobra 248.....................................Breaker only
Cobra 249.....................................Breaker only
Engine
Type..............................................1 cylinder, two-stroke, air
Cylinder displacement ..................185 cc
Speed, crankshaft (strokes/min) ......Full speed: 2550–2650 rev/min
Carburettor ...................................Diaphragm type (Tillotson)
Ignition system..............................Thyristor type, breakerless
Spark plug (recommended) ..........Motorcraft AE-6, BoschW7AC
Spark plug gap .............................1.5 mm (0.06 in.)
Starter...........................................Magnapull
Fuel type.......................................Petrol, 90–100 octane,leaded
Oil type .........................................Atlas Copco two-stroke oil ora
Fuel mixture..................................5% (1:20)
Tank capacity................................1.5 litres (0.39 US gallons)
Fuel consumption .........................Approx. 1.1–1.4 litres/hour
Capacities, Cobra 148, Cobra 149
Max. drilling depth ........................6 m
Penetr. rate with 29 mm drill bit ....300–350 mm/min
Penetr. rate with 34 mm drill bit ....250–300 mm/min
Penetr. rate with 40 mm drill bit ....150–200 mm/min
4

Safety regulations

denotes a hazard or hazardous procedure which CAN lead to serious or
life-threatening injuries if the warning is not observed.
denotes a risk or risky procedure which CAN lead to personal injury or
damage to equipment if the warning is not observed.
Also observe the following general safety rules:
breaker
breaker
cooled
Idling: 1600–1800 rev/min
or unleaded
recommended two-stroke oil
(0.29 - 0.37 US gallons)
(11.8 - 13.8 in./min.)
(9.8 - 11.8 in./min.)
(5.9 - 7.9 in./min.)
G
Use approved personal protective equipment.
G
Use Atlas Copco Genuine Parts only.
G
Always replace worn or damaged signs. The
ordering numbers for signs can be found in
the spare parts list (fig. 1).
Other data
Tool shank ....................................22x108 mm (7/8" x 4 1/4")
Weight, Cobra 148, Cobra 149.....25 kg (53 lbs)
Weight, Cobra 248, Cobra 249.....22 kg (51 lbs)
Length, Cobra 148, Cobra 149 .....745 mm (29.3")
Length, Cobra 248, Cobra 249 .....715 mm (28.1")
Width, max....................................470 mm (18.5")
Connection of grinding machine—see separate in-
structions .
Declaration of noise and vibration emission
Cobra models
Noise according to PN8NTC2
Measured sound
p dB(A)
pressure level
Spread in method and
k
p
production
Measured sound
w dB(A)
power level
Spread in method and
k
w
production
Vibration according to EN28662
Measured vibration
a m/s
value
Spread in method and
k
a
production

Main parts

Illustration shows Cobra 149 (fig. 2A)
A. Choke
B. Throttle lever (Cobra 149, Cobra 249)
C. Vibration-dampened handle
148 149 248 249
99 99 98
dB(A)
4.0 4.0 4.0 4.0
113 113 112 112
dB(A)
4.0 4.0 4.0 4.0
2
8.0 8.5 8.0 8.5
2
m/s
4.7 4.9 4.7 4.9
98