Creative Matting Guide; Double Mat; Off-Set Corner Mat; Inlay Mat - Logan Graphic Products 450 Manual De Instrucción Y Operación

I N T E R M E D I A T E +

Creative Matting Guide

Detailed Instructions on how to cut more creative style mats.
DOUBLE RECTANGLE MAT
(Example 8" x 10" w/3 1 /
Step 1 Set the Mat Guide to 2" and cut an opening in the mat from the BACK.
Step 2 Keeping the fallout piece in place, run double sided tape around the back
of the window border. Do not put tape on cut line. Also put a small
swatch of tape in the center of the fallout.
Step 3 Straight cut a second piece of matboard of desired color to an outside
dimension 7 1 / " x 9 1 /
2
Step 4 Affix the second mat FACE DOWN to the taped back of the first mat being
sure it is centered reasonably well.
Step 5 Set the Mat Guide to 2
out will drop from the window and the mat will be finished and perfectly
aligned. NOTE: Triple mats can be achieved by repeating the above proce-
dures again.

OFF-SET CORNER MAT

(Example 8" x 10" w/5" x 7" opening)
Step 1 Set the mat guide at 2" and draw all four lines.
Step 2 Reset the Mat Guide at 1
Step 3 Leaving the Mat Guide at 1
Bevel Cutting Head and line up the silver indicator line with the bottom
pencil line closest to center of the mat. Cut until the silver indicator lines
up with he top pencil line closest to the center of the mat. Using the
same procedure, cut all four sides. IMPORTANT: At this point the fall-
out will not drop from the window.
Step 4 Remove the mat and reset the Mat Guide to 2". Reinsert the mat.
Step 5 Line up the silver indicator line on the Bevel Cutting Head with the drawn
pencil line furthest from the center of the mat. Cut until the silver indicator
line lines up with the line at the top of the mat furthest from the center of
the mat. Using the same procedure, cut all four sides. NOTE: Be careful to
hold the fallout piece in place as you turn the mat for the last cut.

INLAY MAT

(Example 8" x 10" w/5" x 7" opening)
Step 1 Set the Mat Guide at 2" and cut as per regular instructions.
Step 2 Reset the Mat Guide at 1
again as per regular instructions. You may keep the fallout piece in place
by taping it on the back.
Step 3 Discard the outer border piece and fallout. Retain the inside border cutout.
Step 4 Leaving the Mat Guide in place at 1
color as per regular procedures. IMPORTANT: The second mat must
be of the exact same outside dimension as the first mat.
Step 5 Remove the fallout piece from the second mat and place the inside border
cutout from the first mat in the window opening from the second mat.
The two pieces should fit together like a puzzle creating a flush surface
across the front of the mat. Put tape on back to hold it in place.
L o g a n G r a p h i c P r o d u c t s I n c . , 1 1 0 0 B r o w n S t r e e t , Wa u c o n d a , I L 6 0 0 8 4 To l l F r e e 1 8 0 0 3 3 1 6 2 3 2 w w w. l o g a n g r a p h i c . c o m
Mat Cutter
" x 5 1 / " opening)
2 2
".
2
1 / " and cut the second opening. The double fall-
4
1 / " and draw another set of lines.
2
1 / ", place the mat in the cutter, put on the
2
1 / ". Keeping the fallout in place, cut the mat
2
1 / ", cut a second mat of a different
2

Double Mat

Off-Set Corner Mat
Inlay Mat
M O D E L 4 5 0
10