Tabla de contenido
Publicidad
M a i n t e n a n c e a n d S e r v i c i n g
Pr o c e d u r e s n o t s p e c i f i c a l l y e x p l a i n e d i n t h i s m a n u a l m u s t
b e p e r f o r m e d o n l y b y a q u a l i f i e d t e c h n i c i a n .
T O
PREV ENT S ERIO US INJ URY F RO M
T u r n t h e Po w e r S w i t c h " O
b e f o r e p e r f o r m i n g a n y i n s p e c t i o n , m a i n t e n a n c e , o r c l e a n i n g p r o c e d u r e s .
T O
PREV ENT S ERIO US INJ URY F RO M
D o n o t u s e d a m a g e d e q u i p m e n t . If a b n o r m a l n o i s e o r v i b r a t i o n o c c u r s ,
h a v e t h e p r o b l e m
c o r r e c t e d b e f o r e f u r t h e r u s e .
Cl e a n i n g , M a i n t e n a n c e , a n d L u b r i c a t i o n
1. B EF O RE EACH US E, inspect the general
condition of the air compressor. Check for:
• loose hardware,
• misalignment or binding of moving parts,
• damaged belts,
• cracked or broken parts,
• damaged electrical wiring, and
• any other condition that may
affect its safe operation.
M a i n t e n a n c e S c h e d u l e
Following are general guidelines for maintenance checks of the Air Compressor.
No t e : The environment in which the compressor is used, and the frequency of use can affect how often
you will need to check the Air Compressor components and perform maintenance procedures.
D a i l y :
a. Make sure all nuts and bolts are tight.
b. Drain moisture from air tank.
c. Check for abnormal noise or vibration.
d. Check for air leaks.
e. Wipe off any oil or dirt from the compressor.
* To check for air leaks, apply soapy water to joints while
the Air Compressor is pressurized. Look for air bubbles.
** To clean the compressor surface, wipe with
a damp cloth, using a mild detergent or mild solvent.
D r a i n i n g M o i s t u r e f r o m
The Drain Valve is located under the Tank. It must be used daily to release all trapped air and
moisture from the Tank. This will eliminate condensation which can cause tank corrosion.
CAUT IO N! Do not open the Drain Valve so that more than four threads are showing.
1. Turn the Power switch of the compressor off.
2. Place a collection pan under the Drain Valve.
Page 12
ACCID ENT AL O PERAT IO N:
F F " a n d u n p l u g t h e Co m p r e s s o r f r o m
CO M PRES S O R F AIL URE:
*
**
t h e T a n k
F o r t e c h n i c a l q u e s t i o n s , p l e a s e c a l l 1 - 8 8 8 - 8 6 6 - 5 7 9 7 .
i t s e l e c t r i c a l o u t l e t
2. AF T ER US E, wipe external surfaces of
the compressor with a clean cloth.
3.
W ARNING ! If t h e s u p p l y c o r d o f t h i s
c o m p r e s s o r i s d a m a g e d , i t m u s t b e r e p l a c e d
o n l y b y a q u a l i f i e d s e r v i c e t e c h n i c i a n .
M o n t h l y :
a. Inspect Safety Valve.
3. Unthread the Drain Valve two or three turns ONLY.
4. When all the pressure and moisture is released,
close the Drain Valve.
Item 60637
Publicidad
Tabla de contenido
