Preparation For Use - Symphonic STL1505A Manual Del Usuario

PREPARATION FOR USE

CONNECTIONS
Plug the incoming cable into the ANT jack on the rear of the TV.
Cable
Antenna
OR
TV signal
Incoming cable from home Antenna /
Cable Company (No Cable Box)
Cable Box or
Satellite Box*
OR
IN
Incoming cable from Cable
Company or Satellite Antenna
You can bracket this product as wall mounting TV using the arm adapted for 100mm (commer-
cially available).
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA
PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU'AU FOND.
Note:
•
For your safety and to avoid damages to the unit, unplug the antenna cable from the
ANT jack before moving the unit.
[EXTERNAL CONNECTION]
VIDEO1 input
(OUT)
ex.
Audio Cable
(OUT)
Video Cable
Video Cassette
OR
(OUT)
Recorder
S-Video Cable
Note:
The AUDIO L jack is for mono input. The sound is heard from both speakers. Use this jack for
●
connecting monaural audio equipment.
The S-VIDEO jack is given priority over the VIDEO jack.
●
VIDEO2 input
ex.
(OUT)
Audio Cable
Video Camera
(OUT)
Component
Video Game
Video Cable
Note:
The TV can only accept a 480i (interlaced) video signal.
●
SELECTING AUDIO/VIDEO INPUT
When you use the AUDIO/VIDEO input jacks, select "VIDEO1" or "VIDEO2" mode by
pressing [INPUT SELECT] on the remote control. The input mode changes by pressing the
button as following:
INPUT
TV channel
SELECT
Rear of this TV
OU T
AN T
*NOTE (DO NOT DISCONNECT FROM BOX)
Some cable TV systems use scrambled signals
and require a special converter to receive these
channels. Consult your local cable company.
Rear of this TV
(IN)
(IN)
(IN)
(IN)
Rear of this TV
(IN)
VIDEO1 VIDEO2
INSTALLING THE BATTERIES
1 2
[BATTERY PRECAUTIONS]
• Be sure to follow the correct polarity as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
• Do not mix different types of batteries together (e.g. Alkaline and Carbon-Zinc) or old batteries
with fresh ones.
• If the device is not to be used for a long period of time, remove the batteries to prevent
damage or injury from possible battery leakage.
• Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.
PHOTO STAND
Photo Stand
Adjust the length of the stand in 5 levels to
change the angle of the TV.
OPERATIONS
REMOTE CONTROL AND FRONT PANEL FUNCTION
IR transmitter
To send infrared ray (IR) signal
POWER button
To turn TV on/off
X X Y Y
VOL / buttons
To adjust volume
MENU button
To view on-screen menu
MUTE button
To mute sound
DISPLAY button
To display CH No./Audio Status
Note:
You can test if the remote control sends out the infrared signal with an AM radio.
●
(Refer to "TROUBLESHOOTING GUIDE".)
POWER
MENU Y VOLUME X L CHANNEL K SELECT
Y VOLUME X L CHANNEL K
MENU
VOLUME
To adjust volume
MENU button
To view on-screen menu
Infrared Sensor Window
Note:
If some digits appear in the corner of the screen when the unit is turned on at the first time,
●
press [POWER] without unplugging the power cord.
Install two AAA batteries (supplied)
3
matching the polarity indicated inside
battery compartment of the remote con-
trol.
INPUT
SELECT
INPUT SELECT button
To select TV or external input
POWER
o CH
K K L L
m p CH / buttons
VOL n
1 2 3
Channel number buttons
4 5 6
To select channels
7 8 9
0 +100
MENU
SLEEP button
MUTE SLEEP CH RET
CH RET button
DISPLAY
To return to previous channel
POWER
SELECT
POWER button
To turn TV on/off
SELECT button
K K L L
CHANNEL / buttons
To select channels
X X Y Y
/ buttons