Product Maintenance - Fellowes Powershred 99Ms Manual De Instrucciones

ADVANCED PRODUCT FEATURES
SafeSense
Stops shredding immediately when
hands touch the paper entry.
SAFESENSE
Stops shredding immediately when hands touch the paper opening.
SET-UP AND TESTING
1
2
Turn the shredder Touch test area and
ON ( ) to activate look for the SafeSense
SafeSense indicator to illuminate
®
For more information about all of Fellowes Advanced Product Features go to www.fellowes.com

PRODUCT MAINTENANCE

OILING SHREDDER
machine may experience diminished sheet capacity, intrusive noise when
shredding and could ultimately stop running. To avoid these problems, we
recommend you oil your shredder each time you empty your waste bin.
FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE
2
1
*Apply oil across entry
Press and hold forward ( )
2-3 seconds
*Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250
TROUBLESHOOTING
Overheat Indicator: When the Overheat Indicator is illuminated, the shredder has exceeded its maximum operating temperature and needs to cool down. This indicator will remain
illuminated and the shredder will not operate for the duration of the recovery time. See Basic Shredding Operation for more information about the continuous operation and
recovery time for this shredder.
Bin Open: The shredder will not run if the bin is open. When illuminated, close the bin to resume shredding.
Remove Paper: When illuminated, press reverse (
SafeSense ® Indicator: If hands are too close to the paper entry, the SafeSense
is active for 3 seconds, the shredder will automatically turn off and the user must press the power button on the control panel to resume shredding.
LIMITED PRODUCT WARRANTY
Limited Warranty: Fellowes, Inc. ("Fellowes") warrants the parts of the machine to be free of defects
in material and workmanship and provides service and support for 1 year from the date of purchase
by the original consumer. Fellowes warrants the cutting blades of the machine to be free from defects
in material and workmanship for 7 years from the date of purchase by the original consumer. If any
part is found to be defective during the warranty period, your sole and exclusive remedy will be repair
or replacement, at Fellowes' option and expense, of the defective part. This warranty does not apply in
cases of abuse, mishandling, failure to comply with product usage standards, shredder operation using
an improper power supply (other than listed on label), or unauthorized repair. Fellowes reserves the
® Technology
TECHNOLOGY OPERATION
®
3 4
SafeSense is active and If hand is held on SafeSense
®
working properly area more than 3 seconds,
®
shredder will shut off
CLEANING AUTO-START INFRARED SENSORS
Paper detection sensors are designed for maintenance free operation. However, on rare occasions the sensors
may become blocked by paper dust causing the motor to run even if there is no paper present.
(Note: two paper detection sensors are located in the center of the paper entry)
TO CLEAN THE SENSORS
Turn off and unplug
shredder
SilentShred™ Technology
shreds without noisy disruptions.
WHEN IN SLEEP MODE
1
In sleep mode
®
2
1
Locate Auto-start
infrared sensor
® indicator will illuminate and the shredder will stop shredding. If SafeSense
right to charge the consumers for any additional costs incurred by Fellowes to provide parts or services
outside of the country where the shredder is initially sold by an authorized reseller. ANY IMPLIED
This warranty gives you specific legal rights. The duration, terms, and conditions of this warranty are
law. For more details or to obtain service under this warranty, please contact us or your dealer.
Sleep Mode
Energy saving feature shuts down
automatically after 2 minutes of no
shredding activity.
SLEEP MODE OPERATION
Energy saving feature shuts down the shredder after
2 minutes of inactivity
3
2 2
or
To get out of sleep mode
insert paper
touch control panel
.
3
4
Dip cotton swab in
rubbing alcohol away any contamination
from the paper sensors
®
3