Putting Into Operation - Bpt TARGHA GSM VR Manual Del Usario

Warning
Check with the telephone provider that the SIM is enabled for SMS traffic. We
recommend you check it is working correctly by using it in a normal mobile
phone; it is particularly important to:
• disable the request for the PIN number every time it is switched on;
• try out sending and receiving SMS messages;
In the event of problems:
• Check the remaining credit (on prepaid SIMs);
• Check and if necessary enter the number of the Service Centre (refer to the
phone provider).
The SIM card will probably be supplied to you in a holder that is compatible with
the devices that use full-size SIMs.
1. Carefully detach the SIM from the holder to make it the right size for the
PLUG-IN.
2. Make sure that the device is turned off, disconnecting the power supply.
3. Identify the SIM slot.
4. Insert the SIM in the specific SIM holder with the contacts downwards, check-
ing that the cut-off corner is correctly positioned.
5. Slide the SIM into the slot by pressing it down. If you have any difficulty do not
force the SIM holder but check it is in the right position.
Connecting external aerial
Once installation of the SIM is completed, you can connect the external aerial:
make sure that the device is turned off, disconnecting the power supply; insert
the external aerial connector of the GSM modem connector until it locks.
If you have any difficulty do not force the connector but check it is in the right
position.
The TARGHAVR GSM is ready for optimum operation only once registration with
the GSM network has been completed, and with a good GSM signal.
The GSM signal can be checked in 2 ways:
· Via a mobile phone
G
· Via the GSM LED

Power supply
Warning. The voltage supplied must not be greater than the maximum value
shown, or else the product may be damaged.
Power up only when installation has been completed, i.e. when all the connec-
tions have been made correctly.

Putting into operation

Once installation is completed, it will be necessary to reprogramme the product.
During first switch-on check the key lighting LEDs. 45 seconds after switch-on,
the entry panel will be registered with the network, the LED
flash slowly; if the LED stays on permanently, turn off and check:
• The SIM has been inserted in the slot correctly;
• The PIN number request has been disabled;
• The quality of the GSM signal, by inserting the SIM card into a mobile phone;
• The external aerial has not been connected wrongly.
We would advise that BPT S.p.A. a Socio Unico assumes no responsibil-
ity in relation to the following events:
• failed send, failed receipt or delayed send or delayed receipt of the
SMS message by the entry panel, when this can be attributed to re-
ception of the relative signal or to problems of any nature relating to
the business of the telephone provider;
• charge to credit remaining on entry panel's SIM of costs arising from
messages coming from the mobile phone provider or from other ser-
vices carried out by the mobile phone provider.
10
Replacing name card
To write the desired information on the name card, take out the card holder and
the card.
Personalised name cards up to a maximum thickness of 2mm can be used.
Connections
a SIM-Card input slot;
 GSM LED;
 Aerial Input;
 Reset button;
Terminal board
 Positive Power Supply;
 Negative Power Supply;
 Common relay 1;
 NO relay 1;
 Common relay 2;
 NO relay 2;
Settings
Setting TARGHA GSMVR is carried out by sending simple SMS messages from
a normal mobile phone to the telephone number of the SIM CARD inserted in
the product.
The settings commands are accepted and stored by the entry panel
only if the SMS message is preceded by the correct system PIN (default
0000), otherwise the message will be ignored. TARGHA GSMVR, after
correctly receiving the SMS text message and in the cases for which
it is set up, answers the sender, via an SMS message, confirming the
command has been set up.
G
 will begin to
E
G