Multiplex EasyStar BL Tuning Manual De Instrucciones página 4

!
These operating instructions are an integral part of the
product. They contain important information and safety
notes, and should be kept in a safe place at all times. Be
sure to pass them on to the new owner if you ever dispose
of the product.
1. I
NTRODUCTION
The brushless TUNING power set for the EasyStar offers
the advanced pilot an ample amount of excess power
with a 3S LiPo battery - ideal for simple aerobatics and
windy weather. With a 2S LiPo battery the power set is
ideal for the beginner. The motor pulls the aircraft up to
an impressive altitude very swiftly. The matching 3S LiPo
battery is included in the set.
2. C / R
ONTENTS EPLACEMENT PARTS
• 1 Himax B 2810-2150
• 1 MULTIcont BL-20 S-BEC speed controller
• 1 5.5" x 4.5" propeller
• 1 propeller driver
• 1 Li-BATT eco 3/1-2000 (M6)
3. T . O
YP PERATIONAL
S "E S BL-TUNING"
ET ASY TAR
2S LiPo / 5.5" x 4.5" prop
3S LiPo / 5.5" x 4.5" prop
Recommended flight battery:
For beginners:
MULTIPLEX Li-BATT eco 2/3000
For Advanced:
MULTIPLEX Li-BATT eco 3/2000
Do not use the supplied Himax B 2810-2150 motor with
more than 3S LiPo or 9 NiXX cells when using the
recommended propellers.
4. S N
AFETY OTES
The power set "EasyStar BL-TUNING" is designed
exclusively for use in modelling applications. Incorrect
use can result in serious personal injury.
• Read the instructions before initiation
• Before every flight, check that the motor and propeller
are securely mounted
• Remove all movable objects from the area around the
propeller before switching the motor on
• Do not allow clothing or any of your extremities to get
close to the spinning propeller
• Never start running the motor in your hand
• Stop the motor immediately if you notice vibration.
Eliminate the cause of the vibration before running it
again; you may need to correct the balance of the
propeller blades
• Make sure the power system is adequately cooled; do
not allow anything to obstruct the free circulation of air
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de
Operating Instructions for Power Set "EasyStar BL-TUNING"
# 33 3043
# 7 2288
# 73 3146
# 33 2300
# 15 7231
D P
ATA OF OWER
Current drain: approx. 10.0 A
Current drain: approx. 17.0 A
# 15 7235
# 15 7231
5. A O
SSEMBLING
"E S BL-TUNING"
ASY TAR
Motor mounting during assembling of the model:
1. Glue the Himax BL-motor into the left half of the
fuselage, making it protrude by approx. 3 mm as
illustrated in fig.1 and 2. Secure the motor only
punctual with Zacki ELAPOR
you would be able to unhinge it again, later. Ensure
that no glue gets into the motor.
2. Lay the motor cables in the corresponding cable
channel, as illustrated in fig.1. The cables must be
entirely covered by the foam, you have to deepen the
cable channel, if needed.
3. Fix the driver to the motor shaft
4. Fix the Propeller (impressed script shows backwards)
to the driver by using the included spinner
Fig.1
Fig.2
T P S
F HE OWER ET
in the fuselage, so that
®
Page 1/2